Karnataka Power Transmission Corporation Limited - Karnataka

36798755 a.design, fabrication, galvanizing & supply of 66kv kptcl nbt d/c transmission tower (dd+3), materials including stubs.b.supply of galvanized bolts & nuts weight as per 66kv kptcl nbt design.c.supply of tower accessories like phase plates, number plate, circuit plate, danger plate, earth bond 450mm long.d.supply of coyote acsr conductor, single tension clamps with arcing horns for coyote acsr conductor, single tension clamps for ground wire,66kv polymer disc insulators, pre formed armour rods, vibration dampers, 7/3.15mm g.i.wire for ground conductor & pg clamps for coyote.e.conducting detailed survey along with approved route duly following the route alignment marking stones and submission of detailed line schedule, tower schedule & land schedule for the transmission line construction (plain terrain).f.check survey & tower spotting i) sorting of tower parts made of fabricated angle iron ii) setting up of stubs, templates and aligning dismantling and transportation of template from one location to another location iii) assembling & erection of tower including tightening of bolts & nuts including loading, unloading at site including the weight of stubs. iv)welding of bolts and nuts upto cross arm level. g.supplying and fixing a.c. devices & supplying and fixing barbed wire as per specifications.h.releasing of coyote conductor from t 14 to t 16, stringing of coyote conductor from t 14 anchor point to 15a(dd+3), releasing &stringing of ground wire from t 14b to t 16c.i.fixing of danger board, number plate, phase plate & circuit boards.j.grounding of tower including the cost of 40mm dia 2.5mm thick c class pipe 3mts long with 50x6mm g.i. flat 3mtr. long salt & charcoal including excavation charges.k.loading & unloading of tower parts with hard wares and watch & ward.l.civil works like excavation for dd+3 nbt tower in dry fissured rock for 31 40 deg deviationm. backfilling with excavated soil, supplying and providing tmt steel reinforcement, etc.n.concreting and curing for transmission line towers, concreting and curing as per specification including cost of materials, t&p materials and labour charges with all lead and lift for transmission line towers(i. i) 1:1.5:03[m 20, raft foundation] with form box to be supplied by the contractor,ii) 1:03:06[m 10, basement] with form box to be supplied by the contractor)o.any other work as specified in the tender document on total turnkey basis. providing intermediate tower for increasing the vertical clearance of existing 66kv mulbagal nangli s/c line between t no 15 and 16 near sonnavadi, mulbagal nh75 limits in tlm section kgf, tlm sub division kolar, tl&ss division kolar coming under the jurisdiction of tr(m.), braz circle, kptcl, bengaluru on total turnkey, two part & percentage basis...

Karnataka Power Transmission Corporation Limited - Karnataka

36748150 1. design, fabrication, galvanizing & supply of 66kv kptcl nbt dc transmission tower ( dd+6 ) , materials including stubs.2. supply of galvanized bolts & nuts weight as per 66kv kptcl nbt design.3. supply of tower accessories like phase plates, number plate, danger plate, earth bond 450mm long.4. supply of coyote acsr conductor, single tension clamps with arcing horns for coyote acsr conductor, single tension clamps for ground wire, disc insulators 90 kn, pre formed armor rods, vibration dampers, 7 / 3.15mm g.i. wire for ground conductor.5. conducting detailed survey along with approved route duly following the route alignment marking stones and submission of detailed line schedule, tower schedule & land schedule for the transmission line construction.6. check survey & tower spotting:i ) sorting of tower parts made of fabricated angle iron.ii ) setting up of stubs, templates and aligning dismantling and transportation of template from one location to another location. iii ) assembling & erection of tower including tightening of bolts & nuts including loading, unloading at stores and site including the weight of stubs. iv ) welding of bolts and nuts upto height of bottom cross arm level. 7. supplying and fixing ac devices: supplying & fixing gi angle iron of size 45x45x5mm 1 meter long with cleats bolts & nuts as per specification & fixing above 0.5m length each at inner & outer surfaces if towers to facilitate. running of barbed wire.8. releasing and re stringing of ground wire from t 40 to t 42.9. releasing of coyote conductor from t 40 to t 42.10. stringing of coyote conductor from t 40 to proposed t 41 dd+6 tower.11. fixing of danger board, number plate, phase plate & circuit boards.12. grounding of tower including the cost of 40mm dia 2.5mm thick c class pipe 3mts long with 50x6mm g.i. flat 3mtr. long salt & charcoal including excavation charges13. loading & unloading of tower parts with hard wares and watch & ward.14. civil works like: civil works like: excavation for dd+6 nbt tower in dry fissured rock for 31 40 degree deviation.15. backfilling with excavated soil available near the tower and consolidation layer by layer.16. supplying and providing tmt steel reinforcement cutting, bending, hooking, placing in position, lapping and / or welding whenever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design.17. concreting and curing for transmission line towers, concreting and curing as per specification including cost of materials, t&p materials and labour charges with all lead and lift for transmission line towers i ) 1:1.5:03 [ m 20, raft foundation ] with form box to be supplied by the contractor.18. concreting and curing for transmission line towers. concreting and curing as per specification including cost of materials, t&p materials and labour charges with all lead and lift for transmission line towers i ) 1:03:06 [ m 10, basement ] with form box to be supplied by the contractor.19. any other work as specified in the tender document on total turnkey basis. tender for the work of increasing vertical clearance in 66kv malur hoskote line 1 line by replacement of existing t41 ( sa+0 ) tower by nbt dd+6 tower near itc factory, gangapura limits, malur taluk in tlm section kgf, tlm sub division kolar, tl&ss division kolar coming under the jurisdiction of trm braz circle kptcl bengaluru on total turnkey two part and percentage basis...

Karnataka State Road Transport Corporation - Karnataka

35142079 procurement of fuel injection pipes & leak off pipes. , 207329100102, assy tube 6 od x 2060 long, 2073 4680 0107, suction line hose assly, 2073 4680 0109, press.line hose assly, 2073 4680 0110, return line hose assly, 2073 4680 0111, return line hose assly, 2073 4760 0108, assy.tube with crimped rhose complete, 2077 4680 0157, suction line hose assly, 2085 2910 0101, pipe assy [ 6 dia 1510 long ] , 2085 2910 0102, connnecting line, 2085 2910 0104, assy tube 6 o.d. x 1630 long, 2085 4680 0101, power steering hose pipe ( both side thread ) , 2574 4680 0104, hose 3 / 8 with wire guard, 2751 4290 0101, hose assembly 1 / 2, 2780 4290 0127, nylon pipe set, 2782 4290 0135, assy. nylon pipe 6 dia x 2665 long, 2786 0198 9924, tube injector fuel supply, 2786 0198 9925, tube injector fuel supply, 2786 0798 9901, tube inj. fuel sup / delivery line 1 to 3 set, 2786 0798 9902, tube inj. fuel sup / delivery line 4 to 6 set, 2786 0799 9947, tube injector fuel supply, 2786 0999 9947, tube fuel supply, 2786 0999 9948, tube fuel drain, 2786 0999 9952, tube fuel supply, 2786 1499 9943, leak off pipe [ manifold fuel ] , t06560000001, tube fuel supply flexible pipe, t06560000125, hose plain, t06560000193, hose plain bs iii, t06560000084, hose plain bs iii, 2786 0999 9916, tube fuel supply tc small, 2786 0999 9950, tube fuel supply tc big, 2786 0799 6904, tube fuel supply, 216347600117, diesel return pipe bsiv, 216329100148, m c pipe, 570107996905, tube fuel drain, 216349200174, urea air mix pipe bsiv, 570107990103, manifold pipe ( common rail bsiv ) , 278601999946, hose plain tata, 263243910143, assy teflon hose, b5j06204, hose assy, b4378106, pipe long 300 [ dual valve to air tank ] , b4410313 , diesel main pipe long f 1905415 / al 2386 / al 2388, b4439701, hose 9mm dia bsiii & bsiv, b4439702, fuel flexible hose bs iii, b4439703, s / a fuel hose 550mm 2516h, b4439704, fuel flexible pipe bsiii [ filter to fip ] , b4439706, fuel flexible pipe bsiii, b4461903, hose assy strainer to feed pump, b4464901, hose assly, b4464902, hose assy [ filter ti fip ] , b7007801, s / a of pipe, b7014802, oil strainer pipe, b7015701, breather hose with inner spg, b7015815, injector overfolw pipe hino / euro ( x 1923510 ) , b7022810, s / a oil pipe, b 7049503, over flow pipe bsii 6dti, b 8249515, fip pipe set [ 1 to 6 ] bs ii, b 8250501, sa of pipe oil compr.lubrica, b 8764901, injector pipe 1 bsiii, b 8764902, iinjector pipe 2 bsiii, b 8764903, injector pipe 3 bsiii, b 8764904, injector pipe 4 bsiii, b 8764905, injector pipe 5 bsiii, b 8764906, injector pipe 6 bsiii, b 8764907, leak off pipe euro iii, b 8764909, s / a of leak off pipe ( flexible ) e3, b 8764910, fip pipe set ( 1 to 6 ) , b9290001, sa of pipe injector no.1, b9290002, sa of pipe injector no.2, b9290003, sa of pipe injector no3, f1939660, fuel hose, b8619701, leak off pipe midi bsiv, b8619702, pump to rail 1 midi bsiv, b9274901, fip pipe no. 1 bsiv, b9274902, fip pipe no. 2 bsiv, b9274903, fip pipe no. 3 bsiv, b9274904, fip pipe no. 4 bsiv, b9274905, fip pipe no. 5 bsiv, b9274906, fip pipe no. 6 bsiv, b5j00305, diesel main pipe midi bsiv, b5j00303, fuel return nylon hose bsiv, b9600301, midi bus 1 & 2nd pipe ( pump to rail ) , id205490, fip pipe no. 1, id205491, fip pipe no. 2, id205492, fip pipe no. 3, id205493, fip pipe no. 4, id205494, fip pipe no. 5, id205495, fip pipe no. 6, id205723, fip oil supply, ms603071, fuel hose, f3604310, spring, id000737, fip pipe no. 1 eicher, id000738, fip pipe no. 2 eicher, id000739, fip pipe no. 3 eicher, id000740, fip pipe no. 4 eicher, id000741, fip pipe no. 5 eicher, id000742, fip pipe no. 6 eicher, 207343900237, assly metal line ac crimped hose, 278613996903, tata tube cpr water inlet hose, 278613996904, tata tube cpr water outlet hose, 270029100109, tata clutch m c pipe, b4404301, leyland bsiii nylon hose, b8324804, leyland bsiii nylon dbv hose, ic323844, eicher crimped hose assly 570, id317157, eicher high pressure pipe, id336726, eicher pip [ e coolant out, id335389, eicher pip [ e coolant in, id342081, eicher pipe compressor outlet, id204669, eicher pipe compressor inlet, id312854, eicher pipe fuel return, id330980, eicher pipe fuel return, id320779, eicher pipe fuel inlet, 216543900230, tata bsiv metal ac pipe, b8619721, l / l bsiv automiser pipe, id302461, eicher hose outlet, b8619713, hp line rail inj 1, b8619714, hp line rail inj 2, b8619715, hp line rail inj 3, b8619716, hp line rail inj 4, 278650105845, rub hose 6id x 55 mm, b5j28701, suction line fuel to tank pre filter, b5j28702, suction line pre filter to hand primer, b5j28703, suction line hand primer to main filter, b5j28704, return line engine to fuel tank, b5j28705, suction line main filter to fip ( edc ) , b2g301404, ll bs4 coolant inlet pipe, b2g301406, ll bs4 coolant outlet pipe, b8781204, ll pipe water outlet, b8781203, ll pipe water inlet, 206742900154, tc ac hose pipe, b8619710, injector leak off pipe, b8619723, h p pipe rail to injector, id317757, h p pump to common rail, id336784, hp pipe, 100900340 / p1000529, a c head hose pipe, 252509120260, leak off pipe bsiii tv, b2w00609 / 87089900 / b9290007, injector pipe bsiii ll, f8218200, power steering hose pipe bsiii ll, f8279500 / b2277007 / b9277008, power steering hose pipe bsiii ll, b2w00605, automizer pipe, id336365, pipe bunch assy add blue bsiv eicher, b8619717, high pressure pipe, pump to rail line 1, b8619718, hp piper for cb18, pump to rail line 2, b8619719, high pressure pipe, rail to injector line 1, b8619720, high pressure pipe, rail to injector line 2, b8619722, high pressure pipe, rail to injector line 4, b8619724, high pressure pipe, rail to injector line 6, b2w00605, pipe, injector leak off, id317158, fuel leak off pipe eicher bsiv, id317151, assy high pressure pipe 1 eicher bsiv, id317152, assy high pressure pipe 2eicher bsiv, id317153, assy high pressure pipe 3eicher bsiv, id317154, assy high pressure pipe 4 eicher bsiv, id317155, assy high pressure pipe 5 eicher bsiv, id317156, assy high pressure pipe 6 eicher bsiv, id328531, pipe assy, fuel suction, id336734, fuel pipe bunch assy, id328716, fuel return supply pump, id328536, pipe assy fuel filter, id328538, pipe assy, filter out fip in, id336237, hose fuel return line, id317165, high pressure pipe 1 eicher bsiv, ia332368, suction pipe assy, ia212088, suction pipe assy, b8785330, pipe pump overflow, b8619711, hp pipe from fip to rail line 1, 252507140248, assy fuel pressure line 6, 252507140247, assy fuel pressure line 5, 252507140246, assy fuel pressure line 4, 252507140245, assy fuel pressure line 3, 252507140244, assy fuelp ressure line 2, 252507140205, assy fuel pressure line 2, 252507140243, assy fuelpressure line 1, 252507140204, assy fuelpressure line 1, 252509120307, assy overflow line, 252509120306, assy overflow line, b8250501, sa of pipe oil compr.lubrica, b8742504, sa pipe eng block to compressor, b8781203, air compressor hose inlet bsiii / bsiv, b8781204, air compressor hose outlet bsiii / bsiv, x7478200, high pressure pump bsiv, b8619704, fip pipe no 1 bs iv midi, b8619705, fip pipe no 2 & 3 bs iv midi, b8619707, fip pipe no 4 bs iv midi, 2786 0798 9949, tube fuel drain, 570107996928, tube fuel drain, t06560000036, tube fuel drain bsiii., f1904315, fuel line big, f1904415, fuel line small, al 2253, fuel line pipe 17x19, al 2254, fuel line pipe 19x19, b8619721, hp pipes rail to injector 3rd, b8619722, hp pipes rail to injector 4th, b8619724, hp pipes rail to injector 6th, b5j37802, hose assy return line, ms602053, hose 6x310, id320900, reducer hose, id330980, return hose, 25250714 0291, set fuel pressure pipe assy;pump to rail, 25251313 0159, assy pipe with ferrule ( 230cc comp, 25251817 0205, assy. lube line ( flexible imperial auto ) , 25251813 0162, assy oil line ( oil filter to fip ) , 25252314 5810, rubber hose ( a / c to egr outline ) , 25252314 0129, assy crimped hose with pipe, p5104780, s / a of vibration damper & clip, b4455102, rubber ended hose return line, x2009400, temperature sensor, ff403400, proximity sensor, b5j06203, hose assly strainer to feed pump, id205056, hose, fip ( 130 kw ) , ms603031, hose fuel ( 8x400 ) , id340451, reducer hose 6x8x400, id205781, pipe inelt primer, id320777, pipe, filter inlet, id312853, suction hose, id313059, pipe fuel supply feed pump hcb, id311680, reducer hose, ms603041, hose fuel, ms602013, hose fuel 6x110, id202513, pipe overflow ( hcv, id201238, pipe over flow ( tci ) , ms602061, hose, pipe overflow ( 6x150 ) , id000742, pipe fuel injection 6 ( 6x2 130kw euroii ) , id000741, pipe fuel injection 5 ( 6x2 130kw euroii ) , id000738, pipe fuel injection 2 ( 6x2 130kw euroii ) , id000737, pipe fuel injection 1 ( 6x2 130kw euroii ) , id000739, pipe fuel injection 3 ( 6x2 130kw euroii ) , id000740, pipe fuel injection 4 ( 6x2 130kw euro, 94300323283uc, fip pipe set 1 to 6 bsii ll, b8249602, turbo charger pipe, 286614605801, hump hose, 216314606907, aluminium pipe, 278620999929, hose flexible tata, b9243703, sa pipe outlet main fuel filter, ia329082, hose assy pressure pump, pf 400007, common rail pressure, 2163 4760 0181, t / t bs 3, 12mtr jn.nurm, diesel suction pipe, 2163 4760 0180, t / t bs 3, 12mtr jn.nurm diesel return pipe, id000455, eicher h.p.pipe no. 5, b9290004, s / a of pipe no. 4, b9290005, s / a of pipe no. 5, b9290006, s / a of pipe no. 6...

Karnataka State Road Transport Corporation - Karnataka

34310528 supply of fuel injection pipes & leak off pipes. , b5j06204, hose assy, b4378106, pipe long 300 [ dual valve to air tank ] , b4410313 , diesel main pipe long f 1905415 / al 2386 / al 2388, b4439701, hose 9mm dia bsiii & bsiv, b4439702, fuel flexible hose bs iii, b4439703, s / a fuel hose 550mm 2516h, b4439704, fuel flexible pipe bsiii [ filter to fip ] , b4439706, fuel flexible pipe bsiii, b4461903, hose assy strainer to feed pump, b4464901, hose assly, b4464902, hose assy [ filter ti fip ] , b7007801, s / a of pipe, b7014802, oil strainer pipe, b7015701, breather hose with inner spg, b7015815, injector overfolw pipe hino / euro ( x 1923510 ) , b7022810, s / a oil pipe, b 7049503, over flow pipe bsii 6dti, b 8249515, fip pipe set [ 1 to 6 ] bs ii, b 8250501, sa of pipe oil compr.lubrica, b 8764901, injector pipe 1 bsiii, b 8764902, iinjector pipe 2 bsiii, b 8764903, injector pipe 3 bsiii, b 8764904, injector pipe 4 bsiii, b 8764905, injector pipe 5 bsiii, b 8764906, injector pipe 6 bsiii, b 8764907, leak off pipe euro iii, b 8764909, s / a of leak off pipe ( flexible ) e3, b 8764910, fip pipe set ( 1 to 6 ) , b9290001, sa of pipe injector no.1, b9290002, sa of pipe injector no.2, b9290003, sa of pipe injector no3, f1939660, fuel hose, b8619701, leak off pipe midi bsiv, b8619702, pump to rail 1 midi bsiv, b9274901, fip pipe no. 1 bsiv, b9274902, fip pipe no. 2 bsiv, b9274903, fip pipe no. 3 bsiv, b9274904, fip pipe no. 4 bsiv, b9274905, fip pipe no. 5 bsiv, b9274906, fip pipe no. 6 bsiv, b5j00305, diesel main pipe midi bsiv, b5j00303, fuel return nylon hose bsiv, b9600301, midi bus 1 & 2nd pipe ( pump to rail ) , f3604310, spring, b4404301, leyland bsiii nylon hose, b8324804, leyland bsiii nylon dbv hose, b8619721, l / l bsiv automiser pipe, b8619713, hp line rail inj 1, b8619714, hp line rail inj 2, b8619715, hp line rail inj 3, b8619716, hp line rail inj 4, b5j28701, suction line fuel to tank pre filter, b5j28702, suction line pre filter to hand primer, b5j28703, suction line hand primer to main filter, b5j28704, return line engine to fuel tank, b5j28705, suction line main filter to fip ( edc ) , b2g301404, ll bs4 coolant inlet pipe, b2g301406, ll bs4 coolant outlet pipe, b8781204, ll pipe water outlet, b8781203, ll pipe water inlet, b8619710, injector leak off pipe, b8619723, h p pipe rail to injector, 100900340 / p1000529, a c head hose pipe, b2w00609 / 87089900 / b9290007, injector pipe bsiii ll, f8218200, power steering hose pipe bsiii ll, f8279500 / b2277007 / b9277008, power steering hose pipe bsiii ll, b2w00605, automizer pipe, b8619717, high pressure pipe, pump to rail line 1, b8619718, hp piper for cb18, pump to rail line 2, b8619719, high pressure pipe, rail to injector line 1, b8619720, high pressure pipe, rail to injector line 2, b8619722, high pressure pipe, rail to injector line 4, b8619724, high pressure pipe, rail to injector line 6, b2w00605, pipe, injector leak off, b8785330, pipe pump overflow, b8619711, hp pipe from fip to rail line 1, b8250501, sa of pipe oil compr.lubrica, b8742504, sa pipe eng block to compressor, b8781203, air compressor hose inlet bsiii / bsiv, b8781204, air compressor hose outlet bsiii / bsiv, x7478200, high pressure pump bsiv, b8619704, fip pipe no 1 bs iv midi, b8619705, fip pipe no 2 & 3 bs iv midi, b8619707, fip pipe no 4 bs iv midi, f1904315, fuel line big, f1904415, fuel line small, al 2253, fuel line pipe 17x19, al 2254, fuel line pipe 19x19, b8619721, hp pipes rail to injector 3rd, b8619722, hp pipes rail to injector 4th, b8619724, hp pipes rail to injector 6th, b5j37802, hose assy return line, p5104780, s / a of vibration damper & clip, b4455102, rubber ended hose return line, x2009400, temperature sensor, ff403400, proximity sensor, b5j06203, hose assly strainer to feed pump, 94300323283uc, fip pipe set 1 to 6 bsii ll, b8249602, turbo charger pipe, b9243703, sa pipe outlet main fuel filter, pf400007, common rail pressure, b9290004, s / a of pipe no. 4, b9290005, s / a of pipe no. 5, b9290006, s / a of pipe no. 6...

South Western Railway - Karnataka

32861867 auction sale of condemned released unserviceable ac housing ,blower housing ,filter drum cover manifold elbows ,hydraulic vibration dampers,lube oil filter covers ,drive end couplings ,cam gear covers ,ost housing ,radiator fan housing and miscellaneous loco ms items .weighing 20 mts approx on as is where is basis under the custody sse/dsl/kjm declared vide ds 08 no.230603 dated 26.04.2022 at location :location location bin no.33 at scrap yard dsl shed kjm remarks :1] delivery to be made on actual weighment basis. 2) the purchasers should read published depot conditions and survey the material for road approach, location and qty before bidding to the lot. after bidding no correspondence will be entertained. 3) neighbouring undeclared and nfs items shall not be disturbed. 4) purchaser has to ensure safety of railway material and his labour.5)manual loading is not permitted ....

Indian Navy - Karnataka

25477711 supply of hrly routines on port main engines onboard ins karuva , spares for 12k routine , clamp , bolt hex soc znph r5 f , manifold , sealing ring , ring asm , gasket , oil fill cap , valve keeper wedge , valve rotator , filter element , pin split , indicator air filter restrister , cylinder actuating , washer , washer , washer , washer , washer , pressure reducing va lve assy . , ring sealing , plate first oil cooler , end plate oil cooler , pressure cap ( expans ion tank ) , guide ring , cap pressure expansion tank s2000/4000 , end plate ( sea water cooler ) , ring sealing , first plate see water cooler , rubber bellows , bellows rubber abs c ertd 125 dn 210 bol , cooler plate , first plate ( sea water cooler ) , nut 04 2 , snap ring , ring snap hv znph r5 f , ring snap hv znph r5 f , ring snap hv znph r5 f , ring snap , ring snap , snap ring , ring snap , ground strap , o ring ( 0005330280 ) , o ring for on engine senso , earthing strip , stud , plug , hex screw , hex screw , nut hex , nut hex , nut hex , nut hex , nut hex , nut hex , stud , ring shim , adapter fitting w/si ntered fltr , filter bolt , rotary seal , isolator 60 sh rd314 b 11mn60 , pin grooved , pin grooved , pin spring , pin spring , washer a16 , spring pressure , oil pump , 4/2 way sol . valve ( 0025405497 ) , oil filter spin on , pressure sensor , ring rubber , valve drain , clamp , pin dowel , conical spr . washer , key woodruff a , washer , washer , washer a cop , washer a cop , copper sealing ring , seal ring , washer a , washer a cop , copper sealing ring , washer a cop , copper sealing ring , washer a cop , washer a cop , washer a cop , copper sealing ring , washer a cop , washer a cop , copper sealing ring , copper sealing ring , washer a , copper sealing ring , copper sealing ring , copper sealing ring , copper sealing ring , top compr . ring , oil control ring , compression ring 2nd , air filter , hose metal 32x500 m4 5x1 . 5 , seal ring crankshaft front aux pto , seal ring crankshaft rear , ring seal , ring seal , o ring , washer , bearing angular cont act roller , stud ( 200835008005 ) , support plate ( 200988045000 ) , conical spr . washer , conical spr . washer , ring seal g7 ki ka , gasket kit , hex screw , hex screw , hex screw , hex screw , hex screw , hex screw , sealant pipe thread loctite 586 , ring seal , valve , thrust bearing , washer ( 5110250052 ) , washer , compressor wheel , washer , turbine wheel , piston ring f/turbocharger , ring snap , ring sealing ( 5132155 ) , thermal actuator ( 0052031875 ) , nut , ring cyl liner carbon removal , gasket , cylinder liner size 0 , seal ring ( 5240160319 ) , gasket , bearing thrust/0 0/up/ril/ , crankshaft bearing aux pto end , crankshaft bearing driving end ( ks ) , bearing thrust/0 0/lo/spt/ , crankshaft bearing size 0 0 ( 5240336101 , crankshaft bearing lower half , bolt m20 1 . 50 x 103 . 0 lg 18 conrod , bushing conrod size 0 , conrod bearing upper half , bearing camshaft std , valve guide , exhaust valve , inlet valve , adjusting screw for rocker arm , bushing , pressure relief valve ( 5240700146 ) , fuel line , fuel line , adapter , conn fuel rail rear , thrust member , fuel delivery pump ( 5240900850 ) , pin , shaft ( 5240980111 ) , rubber stop air inlet hsg , gasket , gasket , pressure valve assy . , circlip , nut rotor cover centrifugal spinner fltr , pin , plate , spacer sleeve , gasket , gasket , seawater line , cover , flap ( 5249870051 ) , plug with o ring , grommet , o ring , o ring ( 5249970545 ) , adapter 60deg m14x1 . 5 , cylinder , shaft , flange sealing , bearing bushing , bushing bearing , bushing bearing , shaft , spiral housing , shaft wat pump ht co oling circut , shaft wtr pmp hi tem p clg circuit , wiring harness to in jector , wiring harness for on engine senso , seal oil pan 4569lg , seal strip , sealing ring , sealing ring , o ring , o ring , tube asm cyl head fu el return , spring torsion , gasket , cylinder actuating , oil separator filter insert , diaphragm f oil separator , gasket , sealing ring , gasket , gasket , restrictor flow , flange , ring sealing , gasket , gasket , gasket , ring sealing , bolt banjo a4 , bolt banjo a8 s2000/ 4000 , washer tab locking 8 . 4 st52 3 03 , clamp half tube 2/1 d9 22 , clamp half tube 2/1 g8 22 , grommet , grommet , grommet , grommet , grommet , grommet , grommet , sleeve rubber , seal oil 48 x 72 x 8 mnn386 , screw fitting union , plate , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , bearing cylindrical roller , hose , hose , hose , hose , hose , hose , regulator fuel retur n 0 . 5 bar , valve check 0 . 2 bar rhdk 18 l 0 . 2 , check valve , spacer , spacer , union , o ring , gasket , gasket , gasket , paper pack centrifugal spinner filter , repair kit , compensating washer , cover , valve , sealing ring , valve , cover fixing kit , gasket , screw , nut , washer , washer , washer , screw , repair kit , repair kit , gasket kit , repair kit , v band clamp , gasket , parts kit ( 8699970331 ) , sealing ring , sealing ring , clamp , clamp , nut , cone sealing , union , union , connector 13/8 , union 13 , union , clamp , clamp , vibration damper , injector ( r0010106951 ) , injection pump ( r5260701101 ) , ring carrier , washer , washer , impeller for seawater pump , fuel filter spin on , bearing bushing , bearing bushing , pressure sensor ( x00038945 ) , cover for solas , gasket kit , repair kit , silencer , pipe , servo locker , compensating ring , conrod bearing size 0 0 , gasket for cylinder head , pushrod , swing foll . , flow restrict valve , link ( x52408100002 ) , link , plate guard g73 , idler gear , parts kit , spare parts kit , cylindrical roller , washer ( z=45x23 . 5x2 . 5 ) , cost of services , service charges for 12k routines , packing & preservation charges , transportation charges for karwar to pune and pune to karwar/mumbai , installation & commission...

Karnataka Power Transmission Corporation Limited - Karnataka

24751967 combined package for the works of1 ) replacement of existing t 34 of a+6 ( zig zag tower ) type by dc b+6 extension tower of kalpatharu design in 66kv sc chinthamani yenigadale sc line near somayajalahalli road limits.2 ) providing intermediate tower of d+0 type narrow based kptcl design tower in sc 66kv iragampalli line at loc between no 5&6 near gopasandra limits on partial turnkey basis in tli section chintamani, tlm s / d kolar in tl&ss division, chintamani coming under tr ( m ) circle, braz, kptcl, tzb. : 1 ) a ) design fabrication galvanizing and supply of mild tensile 66kv dc type b+6 meter extension tower including stubs weight as per kalpatharu design. b ) supply of galvanized bolts, nuts as per kalpatharu design and various tower accessories and miscellaneous materials etc. c ) supply of disc insulators, tension clamps, double tension, single tension clamps, pg clamps vibration dampers for coyote acsr , ground conductor 7 / 3.15mm & msc joint for coyote acsr & ground conductor d ) grounding towers with cost of 40mm dia 2.5mm thick c class pipe 3mts long with 50x6mm gi flat 3mtr long salt &charcoal. e ) check survey, pit marking and sorting of tower parts , setting of stubs, templates, aligning , dismantling and transportation of template from one location to another location. f ) assembling and erection of towers including tightening of bolts , nuts including loading and un loading at stores , welding of bolts & nuts. g ) releasing and restringing of coyote & ground conductors from t1 to t10. h ) civil works including excavation for b+6m nbt tower in dry fissured rock, dry fissured rock without blasting. backfilling with excavated soil available near the tower and consolidation layer by layer , supply & providing tmt steel reinforcement cutting, bending, hooking , placing in position, lapping. concreting and curing for transmission line towers, i ) dismantling of s / c 66kv a+6 type normal tower excluding stubs and bolts & nuts along with loading & unloading of released tower. 2 ) a ) design fabrication galvanizing and supply of 66kv kptcl nbt dc transmission tower ( dd+0 ) including stubs. b ) supply of galvanized bolts, nuts as per kptcl nbt design and various tower accessories and miscellaneous materials etc ( c ) supply of single tension clamps, double tension, pg clamps vibration dampers for coyote acsr & msc joint for coyote acsr & ground conductor. ( d ) grounding towers with cast iron of 40mm dia 2.5mm thick c gi pipe 3mts long with 50x6mm gi flate 3mtr long salt &charcoal. ( e ) check survey and tower spotting and sorting of tower parts , setting of stubs, templates, aligning , dismantling and transportation of template from one location to another location. ( f ) assembling and erection of towers including tightening of bolts , nuts including loading and un loading at stores , welding of bolts & nuts. ( g ) supplying and fixing gi angle iron 45x45x5mm with cleats, bolts and nuts, barbed wire, danger board, number plate, phase plate. ( h ) grounding towers with cast iron of 40mm dia 2.5mm thick. ( i ) civil works including excavation for dd nbt tower in dry fissured rock, dry fissured rock without blasting. backfilling with excavated soil available near the tower and consolidation layer by layer , supply & providing tmt steel reinforcement cutting, bending, hooking , placing in position, lapping. concreting and curing for transmission line towers....

Indian Navy - Karnataka

24174970 tender for 12000 hrly routine on pme , spares for 12k routine , clamp , screw , manifold , sealing ring , sealing ring , gasket , cover , valve collet , valve rotator , filter element , split pin , contam indicator , actuating cylinder , washer , washer , washer , washer , washer , press reducing valve , sealing ring , first plate , end plate , base complete , guide ring , valve cover , end plate , sealing ring , first plate , rubber bellow dn 45 , rubber bellows dn 125 , end plate , first plate , hex nut , snap ring , snap ring , snap ring , snap ring , snap ring , snap ring , snap ring , snap ring , cable , o ring for on engine senso ( 0005330280 ) , o ring for on engine senso , earthing strip , stud , plug , hex bolt , screw , hex nut , hex nut , hex nut , hex nut , hex nut , hex nut , stud , adjusting washer , nipple , vent plug , rotary seal , rubber mount , grooved pin , grooved pin , spring pin , spring pin , dished washer , pressure spring , oil pump , 4/2 way valve , oil filter , pressure sensor , rubber ring , drain valve , clamp , dowel pin , conicl spring washer , woodruff key , washer , washer , sealing ring , sealing ring , sealing ring , seal ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , sealing ring , rectanglr sect ring , oil control ring , taper face comp ring , air filter , hose , seal ring crank shaft front aux . pto , radial lip shft seal , o ring , o ring , sealing ring , washer , anglr cont ball brg , stud , adjusting washer , conical spring washer , conical spr . washer , piston ring , comp . , gasket kit ( 23540304 ) , screw , screw , screw , bolt hex a3c , screw , screw , pipe thread sealant , piston ring , valve , thrust bearing , washer , washer , compressor wheel , washer , turbine wheel , piston ring , snap ring , seal ring ( 05132155 ) , thermal actuator ( 0052031875 ) , nut , carbon scrapper ring , gasket , cylinder liner size 0 , sealing ring size 0 , gasket , crankshaft align brg upper half , crankshaft bearing aux pto end , crankshaft bearing driving end ( ks ) , crankshaft align brg size 0 0 , crankshaft bearing upper half , crankshaft bearing lower half , conrod bolt , bushing conrod size 0 , conrod bearing upper half , camshaft bearing size 0 0 , finished valve guide , exhaust valve , inlet valve , adjusting screw , bushing , press relief valve , fuel line , fuel line , adapter , thrust member , thrust member , fuel delivery pump , pin , output shaft ( 5240980111 ) , stop , gasket , gasket , delivery valve , circlip , rotor cover nut , pin , plate , spacer sleeve , gasket , gasket , seawater line , cover , sealing strip , plug with o ring , grommet , o ring , sealing ring ( 5249970545 ) , union , cylinder , shaft , sealing flange , bearing bushing , bearing bushing , bearing bushing , shaft , volute , sea water pump shaft , coolant pump shaft , x4 injector harness , x2 sensor harness ( 5275306422 ) , profile rubber , o ring , sealing ring , sealing ring , sealing ring , sealing ring , fuel return line ( 5340702832 ) , torsion spring , gasket , actuating cylinder , insert , membrane , gasket , sealing ring , gasket , gasket , flow restrictor , flange , sealing ring , gasket , gasket , gasket , sealing ring , banjo screw , banjo screw , tab washer , clamp half tube 2/1 d9 22 , clamp half tube 2/1 g8 22 , grommet , grommet , grommet , grommet , grommet , grommet , grommet , rubber sleeve , oil seal , screw fitting union , name plate , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , cyl roller bearing , hose , hose , hose , hose , hose , hose , non return valve , non return valve , non return valve , washer , washer , cable gland , o ring , gasket , gasket , gasket , gaiter , repair kit , compensating washer , cover for filter , solenoid valve , seal ring , 2/2 way solenoid valve , cover fixing kit , gasket , screw , nut , washer , washer , washer , bolts geilyser coupling , repair kit , repair kit , gasket ( 8690920032 ) , repair kit , clamp ( 8699950012 ) , gasket , adhesive ( 8699970154 ) , gasket , sealing ring , sealing ring , clamp , clamp , nut , sealing cone , union , union , reduction union , adaptor , union , clamp , clamp , vibration damper , injector , hp pump , ring carrier , washer , washer , impeller for seawater pump , easy change filter , bearing bushing , bearing bushing , high pressure fuel sensor ( x00038945 ) , cover for solas , gasket kit , starter repair kit , silencer , pipe , servo locker , compensating ring , conrod bearing lower half ( x00040714 ) , gasket for cylinder head , pushrod ( 5240500930 ) , swing foll . , flow restrict valve ( 0000787949 ) , link ( x52408100002 ) , link ( 0000910124 ) , plate guard g73 , idler gear ( 5240500705 ) , dished washer kit , dished washer , cylindrical roller , spring retainer , pipe ( invalid for sale ) , cost of services , service charges for 12k routines , packing & preservation charges , transportation charges for karwar to pune and pune to karwar , transportation charges for pune to mumbai and mumbai to pune , installation & commission...

Indian Navy - Karnataka

24136125 12000 hrly routine on pme 12000 hrly of pme , service 1 , clamp , clamp , bolt hex soc znph r5 f , sealant pipe thread loctite 586 , sealing ring , ring asm , gasket , oil fill cap , valve keeper wedge , valve rotator , filter element , indicator air filter restrister , cylinder actuating , pressure reducing va lve assy . , ring sealing , plate first oil cooler , end plate oil cooler , guide ring , cap pressure expansion tank s2000/4000 , plate end sea water clr , ring sealing , plate first seawater cooler , cooler plate , plate first seawater cooler , o ring for on engine senso , earthing strip , adapter fitting w/si ntered fltr , rotary seal , isolator 60 sh rd314 b 11mn60 , oil pump , oil filter spin on , pressure sensor , ring rubber , clamp , pin split , washer , washer , washer , washer , washer , air filter , hose metal 32x500 m45x1 . 5 , seal ring crankshaft front aux pto , seal ring crankshaft rear , ring seal , ring seal , o ring , nut 04 2 , snap ring , ring snap hv znph r5 f , ring snap hv znph r5f , ring snap hv znph r5 f , ring snap , ring snap , ring snap , stud , plug , hex screw , nut hex , nut hex , nut hex , nut hex , nut hex , nut hex , stud , pin grooved , pin grooved , pin spring , pin spring , washer a16 , spring pressure , ring seal , valve , thrust bearing , washer , compressor wheel , washer , turbine wheel , ring seal asm , ring snap , oil separator filter insert , nut , ring cyl liner carbon removal , gasket , cylinder liner size 0 , gasket , bearing thrust/0 0/up/ril/ , crankshaft bearing aux pto end , crankshaft bearing driving end ( ks ) , bearing thrust/0 0/lo/spt/ , crankshaft bearing lower half , bolt m20 1 . 50 x 103 . 0 lg 18 conrod , bushing conrod size 0 , conrod bearing upper half , bearing camshaft std , valve guide , exhaust valve , inlet valve , bushing , tube asm cyl head fu el return , adapter , conn fuel rail rear , thrust member , flap , pin , rubber stop air inlet hsg , gasket , gasket , pressure valve assy . , circlip , nut rotor cover centrifugal spinner fltr , pin , plate , spacer sleeve , gasket , gasket , elbow , seawater line , cover , plug with o ring , grommet , o ring , adapter 60deg m14x1 . 5 , cylinder , shaft , flange sealing , bearing bushing , bushing bearing , bushing bearing , shaft , spiral housing , shaft wat pump ht co oling circut , shaft wtr pmp hi temp clg circuit , wiring harness to in jector , seal oil pan 4569lg , seal strip , sealing ring , sealing ring , o ring , o ring , spring torsion , gasket , cylinder actuating , diaphragm f oil separator , gasket , sealing ring , gasket , gasket , restrictor flow , flange , ring sealing , gasket , gasket , gasket , ring sealing , pin dowel , conical spr . washer , key woodruff a , washer , washer , washer a cop , washer a cop , copper sealing ring , copper sealing ring , washer a , washer a cop , copper sealing ring , copper sealing ring , washer a cop , copper sealing ring , washer a cop , washer a cop , washer a cop , copper sealing ring , washer a cop , copper sealing ring , copper sealing ring , washer a , copper sealing ring , gasket , gasket , gasket , paper pack centrifugal spinner filter , repair kit , compensating washer , cover , valve , sealing ring , gasket , screw , nut , washer , washer , washer , screw , repair kit , repair kit , gasket kit , repair kit , dished washer , gasket , gasket , sealing ring , sealing ring , banjo screw , washer , washer , bearing angular cont act roller , stud , conical spr . washer , ring seal g7 ki ka , hex screw , hex screw , hex screw , hex screw , hex screw , bolt banjo a8 s2000/ 4000 , washer tab locking 8 . 4 st52 3 03 , grommet , grommet , grommet , grommet , grommet , grommet , grommet , sleeve rubber , seal oil 48 x 72 x 8 mnn386 , union 32g 1 1/4 a , plate , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , o ring , bearing cylindrical roller , hose , hose , hose , hose , hose , hose , regulator fuel return 0 . 5 bar , valve check 0 . 2 bar rhdk 18 l 0 . 2 , valve check 1 bar rhdk 18 l , spacer , spacer , union , o ring , clamp , union , union , union 13 , union , clamp , clamp , rubber bellows , bellows rubber abs c ertd 125 dn 210 bol , gasket kit , vibration damper , piston , injection pump , injector , ring carrier , washer , washer , impeller for seawater pump , fuel filter spin on , crankshaft bearing size 0 0 , bearing bushing , manifold f oil separator , pressure relief valve , bearing bushing , cover for solas , gasket kit , repair kit , servo locker , compensating ring , pressure sensor , wiring harness for on engine senso , snap ring , conrod bearing size 0 0 , gasket for cylinder head , seal ring , pushrod , swing foll . , flow restrict valve , link , fuel delivery pump ( 5240900850 ) , adjusting screw for rocker arm , support plate ( 200988045000 ) , 4/2 way sol . valve , bearing bushing , washer , idler gear , thermal actuator , washer , shaft , v band clamp , parts kit ( 8599970023 ) , spare parts kit ( 0009939226 ) , dished washer , spring retainer , cost of services , service charges for 12k routines , packing & preservation charges , transportation charges for karwar to pune and pune to karwar , transportation charges for pune to mumbai and mumbai to pune , installation & commission...

Indian Navy - Karnataka

23296297 tender for short refit work package 50t tug sahas 1 short refit work package: general service. scaffolding ( with material ) to be arranged for survey purpose for a total number of 80 days. quote for services. 2 fire sentries with necessary fire fighting equipment, to fight fire are to be provisioned. quote for services. 3 cleaning of all tanks and provide gas free certificate. the vendor is to be provide all consumables required for cleaning. repair plating, structures and fittings of water ballast tank and fresh water tank as per survey report. damaged area to be blasted up to bare metal and recoated as per existing paint scheme. quote for services. 4 degutting & regutting – removal and refiting of panels ( approx 30 sqm ) and pipes. quote for both services and material. 5 carry out non destructive testing for bollards, fairleads and hull structure including stiffening members in the vicinity. ( a ) survey to be done in presence of nsry / fab survey teams and survey reports to be provided. ( b ) requirement to undertake renewal of structures, based on survey report, to be included in sow. quote for services and material. 6 testing of wt compartment. all tanks, cofferdams and sea tubes which have been repaired by build up / renewal or have been subjected to hot work through welding of pad piece / foundation on any of their boundaries, are to be air pressure tested. the pressure applied should never exceed that which corresponds to a pressure of 0.2 kh / cm2 ( 02 mtr of water or 0.2 bars or 2 1 / 2 ibf / in2 ) . ballast tank qty 03 , fuel tank – qty 05, fw tank – qty 02, misc tank 04. clearance of areas, subject to apt will be accorded by nsry / fab survey team. quote for services . 7 mast and riggings. ( a ) examine mast structure, whip aerial platforms and the surrounding structure on deck, eye plates, load carrying members, for signs of corrosion. examine bolted, riveted and intermittent welded structure connections for signs of fracture. portable and semi portable fittings to be removed for closer examination of structure underneath. defect to be rectified and paint to be restored. all marks of corrosion and rust are to be removed. requirement of paint and other consumables to be catered for by the vendor. quote for services and material. 8 ( a ) test all standing & running riggings fitted on mast structure along with associated fittings. renew all wire ropes and associated fittings as necessary. ( b ) carry out load testing of all deck eye plates ( qty 14 ) , bottle screws ( qty 14 ) and provide load test certificate. damaged eye plates and bottle screws are to be renewed by the vendor, together with relevant load test certificates / guarantee / warrantee. quote for services. 9 steel renewal. any requirement to include transportation of steel and preparation of the plates, including shaping and positioning at location has to be catered for by the vendor.quote for services. 10 funnel. examine, clean and restore paint of eye plates and surroundings structure, funnel structure ( internal and external ) . portable or semi portable fittings that obscure structure are to be removed and to be recoated before the fittings are replaced. requirement to ensure that damaged areas requiring steel renewal together with paint renewal will have to be undertaken by the vendor. quote for services and material. 11 accommodation and office. repair / renewal of wooden furniture and wooden fittings including table, chairs and wooden cupboards in compartment and accommodation spaces. quote for services and material. 12 repair / renewal of bunks, mess lockers and their securing arrangements. lockers and securing arrangements that are beyond repairs, are to be replaced with suitable alternatives. quote for services and material. 13 repair / renewal of defective deck covering and renewal of deck plates underneath as per survey report of yard. deck coverings being renewed, should be those that have been approved by navy. quote for services and material. 14 anchor, chain cable and cable locker. lay out all cables, survey cable and shackles, break, clean and grease all joining shackles, strip and grease slip in cable locker. re arrange cable length to ensure equality of wear. re mark cable length. examine hull associated fittings. examine all spare chain cable and fittings, clean and coat with boiled linseed oil. dismantle anchor. clean and grease trunion pin and housing. grease to be used: lg 280 patt.no. 0474 / 910 0502. hydrojet lasting of the anchor chain cable to be carried out. the machined surfaces of the joints of lugless joining shackles are to be examined for corrosion and all such shackles are to be stripped, greased and re assembled. the anchor, chain and cable locker to be restored to factory fit functionality. quote for services and material. 15 machinery spaces. clean all bilges using approved chemical method. clean out all limber holes and drain holes. examine structures not covered by lagging, paying particular attention to position where water is likely to accumulate, junctions of longitudinal with side platings and machinery bearers with bottom plating, horizontal surfaces such as tank tops, horizontal stiffeners and structure obscured by cable plating. portable fittings that obscure structure are to be removed for examination of structure behind. carry out surface preparation in accordance with no 53 / 16 and recoat the damage paint. disposal of sludge ( approx 50 tons ) to be catered for by the vendor. consumables for cleaning also to be catered for by vendor. paint scheme restoration in all areas as per existing navy standards. quote for services and material. 16 check the condition of the vibration mounts. clean and apply necol lacquer. spm readings of equipment will need to be certified by nsry / engg / ele teams. vibration damping if not adequate, will need to be replaced by the vendor after grouping of mounts. certification i.r.o the same may be provided. quote for services and material. 17 renew damaged / perished lagging at various places using pin method. renew paint scheme of affected areas before renewal of lagging. all consumables are to be catered for by the vendor. quote for services and material. 18 capstan ( oem geeta engg ) . all structural and functional defects pertaining to motor and capstan assembly to be rectified by the vendor by repairs / renewal. requisite fluids to be positioned for lubrication. motor spm values and power ratings for safe operation to be proved during trials. offer for trials to ss post completion. 19 anchor windlass ( oem geeta engg ) . all structural and functional defects pertaining to motor and capstan assembly to be rectified by the vendor by repairs / renewal. requisite fluids to be positioned for lubrication. motor spm values and power ratings for safe operation. offer for trials to ss post completion. quote for services and material / spares. 20 renewal of mushroom head with spindle and valves. renewal to also include safety nets / fasteners as per requirement / joints and gaskets. quote for services and material. 21 sewage treatment plant ( oem – m / s eva coy n40ce ) . ( a ) functioning of level switches of v 1 tank. operate all the valves which have not been changed from a set position to prevent jamming. carryout de sludging of v 2 tank by back flushing line. clean the seawater ‘y’ type strainer at the inlet to ‘bookcell’. check macerator pump oil level by removing the pipe plug located on top of the pump casing. oil to be renewed. vendor to cater for disposal of 5 ton sludge associated with stp system. overhauling of system and auxiliaries to be undertaken. qc coverage for overhauling to be provided by nsry / qc team. ber valves / pipes / joints and fittings to be renewed. all fluid replenishment to be undertaken as required. ( b ) clean air supply filter / regulator element in solvent by removing the screws that secure the air chamber to the filter body. drain, inspect & clean the ‘bookcell’. remove large deposits of hard material with diluted hydrochloric acid. post completion of routines, operate system and inspect for leaks and proper cell amperage. ( c ) inspect the tightness of belt and check leakage from gland of discharge pump. repack the gland ( if required ) . quote for services and material / spares. 22 macerator pump. carry out the following : ( a ) check to ensure there are no leakages from the main seals. renew drive end bearing and seals if required. ( b ) check and ensure that the impeller rotates freely with no vibration. ( c ) inspect and tighten nuts and bolts as necessary. ( d ) check overload units operating correctly. ( e ) check all valves for correct operation. ( f ) remove drain plugs provided at each end of the bracket of the electric motor and allow any accumulated moisture to drain away and replace plugs. note. replacement of the pump assembly to be undertaken by the vendor, if the discharge rate does not meet oem designed standards. quote for services and material / spares. 23 clean and lubricate all plug cock valves. lubricate valves in fully opened or fully closed position only. quote for services and material. 24 ( a ) undertake effluent test from nabl accredited lab and check compliance to marpol norms. ( b ) carry out in situ calibration of fixed h2s sensor. certificate of calibration to be obtained from the oem. date of calibration and next due date should be clearly indicated on the certificate. ( c ) sewage pollution prevention certificate valid for duration of five years from a state authorised accredited agencies as specified in mepc 115 ( 51 ) and 227 ( 64 ) for the ship adopted on 01 apr 04 as per regulation 5 of revised annex iv of marpol 73 / 78 ( ncd 3930, issue 3, sep 16 is relevant ) . quote for services. 25 towing hook with quick release mechanism ( oem m / s nautiluis eng & construction company ) . carry out load testing of towing hook and undertake repairs. job involves serviceability of release line and repairs. replacement of the towing hook with quick release mechanism to be undertaken if existing unit exceeds service life / not functioning as per design. quote for services and material / spares. 26 grease filters inside exhaust trunking in galleys to be cleaned and preserved. renew if defective. quote for services and material. 27 doors water tight and non wt doors. check clips, hinges for looseness and wedge pieces for signs of wear. examine leather washers, toridal sealing rings and rubber sealing. renew worn out parts and carry out chalk test of all wt doors. quote for services and material. 28 scuttles & windows. check hinge fitting, toughened glass and glass rails for looseness and sign of wear / damage. renew worn out parts as necessary. windows – qty 32, scuttles – qty 18. quote for services and material. 29 hatch and manholes. survey hatch and manholes covers. remove and clean hatch and tumbler hinges & pins. apply grease. deteriorated hatches and manhole covers to be fabricated. securing fasteners wherever damaged to be renewed with stainless steel fasteners as per recommendations of survey team. carry out chalk test of all wt hatches and renew worn out parts as necessary. quote for services and material. 30 ladders. repair the ladders with associated footsteps. structural defects in the ladder assembly other than steps also to be catered.quote for services and material. 31 single arm boat davit ( oem hemant engg ) . overhauling of boat davit along with motor assembly. offer for trials to ss post completion. structural and functional defects of the single arm boat davit to be rectified by repairs / renewal of components. quote for services and material. 32 survey wire rope, spare gear and other associated lifting gears. renew as necessary. renewal of wire ropes to be undertaken as per existing naval guidelines. quote for services and material. 33 carry out load testing with davit fully rigged up. after completion of load test, examine the complete davit structure and associated lifting gears for flaws, distortion, defects etc. flaws must be examined and repairs to be undertaken, followed by retesting. quote for services and material. 34 water accumulation observed on both side of foxle. scupper system to be re positioned for clearance of water accumulation. painting in areas affected by hot work / steel renewal to be restored by vendor. quote for services and material. 35 02 bullwark doors damaged. hinges corroded. to be renewed. mat – ms. quote for services and material. 36 bullwark damaged / deformed at various location. to be repaired / renewed. mat – ms. quote for services and material. 37 ( a ) rubber fenders on both side of tug found damaged / perished. fenders to be renewed. length 50 mtr. ( b ) securing fasteners for fenders found perished / corroded. to be manufactured as per sample and fitted back. note. deformation of base structure / strengthening members on to which the fenders are secured are to be surveyed and deformations, if any to be rectified by hotwork / steel renewal. quote for services and material. 38 wooden fenders damaged in port and stbd side. to be renewed. job involves re fitment of fenders on ship side. quote for services and material. 39 natural air vent of all compartments wire mesh broken, air vent corroded, flaps rubber beading perished. hinges and butterfly nuts corroded. to be renewed. quote for services and material. 40 sounding points of fresh water tank threads worn out. to be repaired / renewed. quote for services and material. 41 securing bracket of fire hose box corroded at multiple locations. to be renewed. quote for services and material. 42 lifebuoy with self igniting light and smoke signal ( mob marker ) quick release type to be renew on bridge deck. quote for service and mat. 43 fibre sheet for weather deck canopy damaged. to be renewed. quote for services and material. 44 platform for head bollard corroded / damaged. to be repaired / renewed. quote for services and material. 45 platform for quarterdeck bollard corroded / damaged. to be repaired / renewed. mat wood. quote for services and material. 46 ( a ) fisherman plate along with securing pin corroded. to be manufactured as per existing plate and pin ( qty 02 ) . ( b ) bottle screw for anchor chain stopper corroded. to be renewed ( qty 02 ) . quote for services and material. 47 life raft stowing brackets ( qty 02 ) along with sliding ladder damaged / corroded. to be repaired / renewed and operational. job involves renewal of life raft securing straps. quote for services and material. 48 serviceability checks of life rafts ( qty 02 ) and hru ( qty 02 ) by nabl accredited agency. webbing of life raft to be renewed, if damaged beyond repair. quote for services and material. 49 covers ( both compressor safety mesh cover and control panel cover ) for 02 ac compressor units on upper deck damaged / broken. to be manufactured. mat al plate. quote for services and material. 50 15 cm ms strip on upper deck wt doors damaged / corroded. to be manufactured and welded in situ. quote for services and material. 51 internal super structure repair works to be under taken on internal hull structure including bulkhead and fittings as per survey report. painting to be under taken post repairs. quote for services and material. 52 refrigerator on board defective. to be repaired / renewed. quote for services and material. 53 01 weather deck locker damaged. to be repaired / renewed. quote for services and material. 54 executive chairs fitted at wheel house observed to be damaged. to be renewed. quote for services and material. 55 engine room blower wire mesh and securing ms strips broken / corroded. to be renewed. quote for services and material. 56 sunmica and wooden beading of dining hall table broken / damaged. to be repaired / renewed. quote for services and material. 57 canvas covers of following deck equipment torn / perished. to be renewed. windlass, and control stand, rescue boat, search light ( qty 02 ) , magnetic compass, capstan and capstan control, boat davit motor, me and da exhaust and intake. quote for services and material. 58 anchor cleaning sea water line chocked / damaged. to be repaired / renewed. quote for services and material. 59 mob stand ( qty 04 ) and bracket damaged. to be renewed. quote for services and material. 60 ( a ) foundation of port and stbd search light found deteriorated. repair to be carried out. ( b ) rotating mechanism of port and stbd search lights to be renewed. quote for services and material. 61 hull survey. clean all tank tops, bilges of machinery spaces and other accessible internal surfaces of underwater hull. damaged area to be blasted and paint to be restored as per existing paint scheme. quote for services and material. 62 underwater platings. ( a ) remove marine fouling from the hull using hydro jet with maximum pressure not exceeding 3000 psi. ( b ) areas where breakdown of abrasive anticorrosive paints observed, to be blasted and recoated with full paint scheme. ( c ) paint scheme on full underwater hull and boot top including wind and water areas i.e. area up to 500mm above boot top area is to be restored. ( d ) application of one coat of a / f paint on underwater hull and boot top area to be carried out post adequate surface preparation. quote for services and material. 63 draught marks. draught marks to be painted with paint scheme as under water area and top coat to be painted with white paint. ( a ) fwd ( b ) midship & ( c ) aft. renew defective draught marks. quote for services and material. 64 above water area ( ship side, superstructure and fittings, davit, windlass, capstan ) . ( a ) clean the hull using hydro jet with maximum pressure not exceeding 3000 psi. damaged area to be blasted up to bare metal. ( b ) carry out painting of above water area with high performance ( hpp ) advanced hybrid coating system for above water area ( ship side & superstructure ) as per paint scheme mentioned below: ( i ) 02 coats of primer to achieve 80 microns dft. ( ii ) 02 coats of ral 7040 colour specification to achieve 80 microns thickness. ( iii ) total dft 320 microns. note. navy approved paint to be used. requirement of paint, other consumables and staging to be catered for by the vendor. quote for services and material. 65 life saving appliances. ( a ) stretcher ( qty 01 ) for life saving damaged. to be renewed. size standard. ( b ) first aid box locker damaged at various location. to be renew and fitted on specific locations. ( oem m / s godrej & boyce mfg co ltd. ) . ( c ) life jacket with light and whistle damaged ( qty 19 ) . to be renewed as per ( lsa code msc 207 ( 81 ) ) . testing of life jackets to be carried out. quote for service and material. 66 water filter cum purifier defective / damaged in crew dining hall. to be renewed. job involves fitment. quote for services and material. 67 following defective wc and bathroom accessories to be renewed. ( a ) shower 05, ( b ) water tap 06, ( c ) urinal with full fittings and accessories 03, ( d ) commode with full fittings and accessories 04, ( e ) two way basin / sink 04. note. defective valves and reducers, to be renewed. quote for services and material. 68 carryout chemical cleaning of all trunkings. renew perished / damaged trunkings on upper deck and mess. paint to be restored post repairs as per existing paint scheme ( qty 80 sqm ) . quote for services and material. 69 hose box damaged / broken at various location ( qty 07 ) . securing brackets corroded. to be manufactured and refitted in situ. mat grp. quote for services and material. 70 weather deck & bridge top deck corroded / undulation at various location. hydro blasting to be under taken prior survey. defects to be rectified as per survey report of yard. ( a ) aarea to be painted with high performance non skid coating system for weather decks ( hpp ) paint scheme as mentioned below post defect rectification and plate renewal as per survey report. ( b ) 07 years guarantee paint scheme of da grey colour to be used. ( c ) navy approved paint scheme to be used. ( d ) paint scheme of weather deck and platforms: ( i ) 01 coat primer coat dft 50 microns. ( ii ) 01coat anti corrosive intermediate coat dft 200 microns. ( iii ) 01 coat non skid top coat dft 800 micron. ( iv ) total dft 1050 microns. note. paint to be restored as per paint scheme post repair and inspection. paint to be provided by refitting firm.quote for services and material. 71 combing around wheel house deck corroded / damaged. to be repaired / renewed in situ. mat ms quote for services and material. 72 panelling damaged / corroded at various location. to be renewed. mat ss. job involves removal of existing panels and fitment. quote for services and material. 73 02 mooring rope reel, 01 towing rope reel and 01 cable reel broken. to be manufactured and replaced in situ. job involves welding and cutting assistance and fitment. quote for services and material. 74 ( a ) ships name box along with lighting arrangement defective. to be renewed. mat ms ( qty – 02 ) . ( b ) ships name board on port and stbd side to be renewed. mat wood ( qty – 02 ) . quote for services and material. 75 microtech damaged at various location. removal of old microtech to be undertaken. surface preparation to be carried out for hull survey. defects to be rectified as per survey report of yard. microtech to be renewed post application of primer on deck. quote for services and material. 76 dado area in wet compartment corroded / damaged. to be repaired / renewed. job involves removing of gutting degutting of panels. quote for services and material. 77 heavy duty tyre fenders of barge found damaged. renewal of fenders to be carried out. hot work required for removal and fitment of tyre fenders to be carried out ( qty 20 ) with 60 eye pads and 16 mm galvanised chain along with d shackle. undertake apt of hot work tanks if any. new heavy duty tyre fenders to be provided by firm. quote for services and material. 78 wire mesh and ball valve of air vent on upper decks be replaced if required. structural defects on air vents to be repaired. quote for services and material. 79 strip, clean and overhaul domestic fresh water system valves, stop cock ( qty 05 ) , basin beep cock ( pillar ) ( qty 04 ) , sink beep cock ( pillar ) ( qty 01 ) . mat brass ( chrome plated ) . quote for services and material. 80 ( a ) ventilation flaps of all compartments, wire mesh broken, air vent corroded, flaps rubber beading perished, hinges and butterfly nuts corroded, ventilation lowers damaged / corroded. to be renewed ( qty 16 ) . ( b ) punka lowers damaged at various trunkings. to be renewed and fitted. material to be provided by firm ( qty 05 ) . quote for services and material. 81 cathodic protection sacrificial anodes renew sacrificial anodes fitted to under water hull, voith blade, rope guard, shaft tunnel, stern tubes, inlet and outlets, seachest, biges and cofferdams. 82 enginering dl: ( port and stbd main engine, wartsilla, model : 8l 26 2000h ) : carry out 2000 hourly routine of main engine : ( a ) check engine oil leakage, fixation of piping, cables and wring rectify leakage and loose cable connection. n ( b ) check engine on bolt connection, repair loose bolts. n ( c ) check engine drain points of charge air receiver and possible water. n ( d ) check oil level, charge oil if required. n ( e ) check foundation bolt and chocks. repair if required. n ( f ) renew fuel and lub oil filter. n ( g ) clean centrifugal filer. n ( h ) drain starting air vessels and air treatment units. n ( j ) servicebility checks of ht and lt cooling water. n ( k ) clean air compressor by water injection. n ( l ) inspect and clean air filter to the turbo charger. n ( m ) check function of by pass and waste gate assembly. n ( n ) lubricate fuel control mechanism linkage. n ( p ) check if alarm and safety system is on with running engine, rectify if not working. n ( q ) check function of measuring devices, calibrate if not working properly. n ( r ) check function of oil mist detector, calibrate if not working properly. n ( s ) check operation of turning gear and start inter lock device, repair / calibrate if malfunctioning. n ( t ) check / adjust valve clearance. n ( u ) main engine ups control panel door damaged. to be renewed. n ( v ) main engine fresh water cerculating pump no.1 breaker tripping frequently. defect to be rectified. n ( w ) both me lcp display malfunctioning. to be renewed. n ( x ) turbocharger outlet temperature sensor faulty, to be replaced ( port main engine ) n ( y ) both main engine starting air line water trap valves to be overhauled n ( z ) both pre heater to be dismantled, mechanically cleaned and boxed back. system to be pressure tested and proved for operation post fitment of pre heater. test pr 3 kg / cm2. n ( aa ) both pre hetaer circulating pump alongwith motor to be overhauled n ( ab ) main engine expansion tanks ( qty 03 ) to be cleaned and paint to be restored as per paint scheme. respective sight glass ( qty 01 ) to be renewed. n ( ac ) stbd main engine rpm not exceeding beyond 260 at idle as against 600 rpm, defect to be rectified ( m / s wartsila engine ) n ( ad ) fuel injectors of both main engines to be calibrated ( m / s wartsila engine ) n ( ae ) governor calibration of stbd main engine to be undertaken ( m / s europe actuatore ) n ( af ) excessive lub oil consumption on both main engine. dr to be undertaken n n 83 ( port and stbd da, m / s cummins india ltd, 3000h ) : carry out 3000 hourly routine : n ( a ) remove injectors. clean, inspect, repair & calibrate with new spares. n ( b ) remove heat exchanger. clean & pressure test. n ( c ) remove turbocharger. clean, inspect & repair with new repair n kit ( check turbocharger end play and radial clearance ) ntighten nut & cap screw of air inlet and exhaust system. ncheck vibration damper visuallyrepair if defective. n ( d ) replace belts and accessories. n ( e ) check all cut out & safety controls. renwe if defective. n ( f ) flush cooling system with restore plus, run engine to bring it to operating temperature. stop the engine reflush cooling system with portable water 2 3 times. refill cooling system with coolant. run the engine for three to five minutes. n ( g ) post completion of routines, start the engine and check all gauges, replace if required, check for oil / water leakage, exhaust leakage, stop the engine and recheck engine oil level, top up if required. after necessary inspection restart the engine. run at idle speed for 15 minutes; carry out safety device checks. undertake full load trials on completion. post complition of routine carry out sdc checks and load trails, calibrate / renw defective safety divices. n ( h ) da control panel door damaged. to be renewed. 84 port and stbd voith turbo schneider, model 21 r 5 / 150 2: carry out docking routines and 5000 hourly routines : ( a ) check the screw joint renew if dfective. n ( b ) check for the leakage from blade shaft sealing, if there any keajage rectify it. n ( c ) check for the leakage from main seal, change seal if defective. n ( d ) check main gear toothing for any damage, rpair it if damaged. n ( e ) check the input gear rpair it if damaged. n ( f ) check for the leakage from mounting gear. if there is any leakage rectify it. n ( h ) check for leakage from the propeller well. if there is any keajage rectified it. n ( j ) check for correct fuctionnig of rotor space ventilation repaired it if defective. n ( k ) renew corrosin protection. note. quote for services and material / spares. n 85 fuel and lub oil centrifuge make alfa laval pa 605: carry out five yearly routines on fuel and lub oil centrifuge : ( a ) clean and inspect inlet and outlet pipe threads, paring disc, housings and frame hood. renewed damaged / defective parts. n ( b ) clean and inspect separator bowl, top disc, bowl discs, distributor, nozzles in bowl body, sliding bowl bottom, discharge mechanism, threads on bowl hood and bowl body, bowl spindle cone and bowl body nave, renewed damaged / defective parts. n ( c ) clean and inspect oil mist fan, oil pump, water tank, bowl spindle, ball bearing housing, indentations and radial bobble of bowl spindle, renewed damaged / defective parts. n ( d ) clean oil sump, change oil and oil filling device. n ( e ) clean and inspect friction coupling, renewed if defective. n ( f ) replace electric motor bearing. n 86 ows make suyash, modle sd0.5: carry out five yearly routines : ( a ) replace coalesce. n ( b ) replace adsorber elements. n ( c ) replace stuffing box packing. n ( d ) check stator and rotor, replace worn out component. n ( e ) replace zinc anode. n ( f ) check oil level of pump gear, fill up if required. n ( g ) open the inspection port of the oil separator housing, the oil separator housing and the adsorber housing. replace worn out parts. n ( h ) remove the sludge and clean container. n ( i ) check seal and piston valves, replace damaged seal and components. n ( j ) replace sensor electrode. n ( k ) checks the function of heater, if defective replace it. n ( l ) shore suuply connection box damaged. box to be renewed to ensure water tight integrity. n 87 reciprocating air compressors make elgi ( model hp 10 300 ) : carry out 1000 houlry routines of air compressor : ( a ) change oil. n ( b ) observed noise and vibration. n ( c ) check fasteners, renwed if dfective. n ( d ) check for air leakage, rectify if there any air leakage. n ( e ) adjust pressure setting as per manual. n ( f ) change inlet air filter. n ( g ) clean breather valve. n ( h ) inspect valves, renewed if defective. n ( i ) check nrv, repaired if defective. n ( j ) check cooler, repaired if defective. n 88 co2 fire fighting system: carry out sr yearly routines on co2 fire fighting system : ( a ) carry out survey of piping. repair / renew as required. n ( b ) calibrate weighing beam scale ( where fitted ) . n ( c ) check all flexible hoses for cracks, embrittlement and sign of cracking. renew them after assessing the condition n ( d ) overhaul non return valves and safety stop valves ( where fitted ) . n ( e ) remove and inspect cylinder operating heads. test for correct functioning. n ( f ) renew bursting discs fitted in pipe system ( where fitted ) . n ( g ) weigh the co2 cylinder using beam scale. if the weight falls below 10% of initial weight, recharge the cylinders. maintain record in log book. n ( h ) admit lp air into ring main checking the system for ( j ) leaks. ensure that all the discharge pipes and nozzles are clear. calibrate pressure gauges fitted in the system. n ( k ) check audio visual alarm function, limit switches in control penal for operation, renewed if defective . note quote for services and material / spares 89 serviceability checks of co2 fire fighting control system to be undertaken and repaired with spares as required. note quote for services and material / spares 90 hinges to be provided on chequred plates of engine room for operating system valves. note quote for services and material / spares 91 sea water suction strainers : remove inspect, clean and paint with epoxy coating for following suction strainers : main sea chest, bilge suction and da suction. renew if required. mat ss as per sample note quote for services and material / spares 92 system pipelines : removal, chemical clean and repair system pipelines. pressure testing to 1.5xworking pressure ( kg / cm2 ) , undertake fitment onboard and prove for satisfactory performance : galvanised steel ( a ) 100mm 93 ( b ) 80mm 94 ( c ) 65mm 95 ( d ) 50mm 96 copper. ( a ) 40mm 97 ( b ) 32mm 98 ( c ) 25mm 99 ( d ) 20mm 100 ( e ) 18mm 101 ( f ) 15mm 102 cu ni ( a ) 125mm 103 ( b ) 100mm 104 ( c ) 80mm 105 ( e ) 65mm 106 ( f ) 50mm 107 ( g ) 40mm 108 ( h ) 25mm 109 system pipelines : renew with end fittings, pressure test to 1.5xworking pressure ( kg / cm2 ) , fit onboard and prove. ( a ) air vent & filling system, 150mm 110 100mm 111 65 mm 112 50 mm 113 copper ( a ) lub oil & sanitary system, 40mm 114 32mm 115 25mm 116 20mm 117 18mm 118 15mm 119 12mm 120 both main engine fly wheel safety guards damaged. guards to be manufactured. note quote for services and material / spares 121 flap cover perished, to be renewed n ( a ) stbd main engine exhaust funnel. n ( b ) provision of new dd compressure exhaust outlet flap cover note quote for services and material / spares 122 external fire fighting system make jason engg ais, modle sru c255 vk1.8ccw 02 : port fi fi clutch lub oil cooler to be cleaned and pressure test to be carried out. serviceability checks of system to be undertaken including necessqary spares. note quote for services and material / spares 123 lub oil transfer pump make tushaco, modle r 20 dg : pump to be overhauled view high vibration. note quote for services and material / spares 124 external fire fighting system: actuator of nozzle of fifi system on top of bridge not operating. same to be repaired / renewed note quote for services and material / spares 125 following defects on fifi system n ( a ) clutch not engaging in remote mode. dr to be undertaken. n ( b ) fifi system pipe line cracked / damaged at 08 n locations. leakages to be rectified and system to be pressure tested. dia 300 mm, mat cu ni n ( c ) operating wheels of fifi system valves ( 08 nos ) damaged. same to be renewed. n ( d ) hydraulic valves of fifi system to be overhauled with spares, size 300mm, qty 02 note quote for services and material / spares 126 pressure regulating valves n ( a ) operating at high pressure than normal ( 01 in no ) , to be overhauled ( range 30 to 5 bar ) n ( b ) prv operating at high pressure than normal ( 02 nos ) , to be overhauled ( range 30 to 9 bar ) note quote for services and material / spares 127 both ru tank sight glass damaged. to be renewed. note quote for services and material / spares 128 overhaul air starting motor of main engine, make wartsila note quote for services and material / spares 129 fresh water system filling point at weather deck perished same to be renewed with flanges ( aprrox length 0.25 mtr. mat gun metal, dia 65 mm nnote quote for services and material / spares 130 repair / renewal of hand pump fitted on foxle note quote for services and material / spares 131 following oil pressure setting to be adjusted on both voith : ( a ) lub oil pressure ( b ) control oil pressure , rotor oil pressure. 132 voith turbo schneider, model 21 r 5 / 150 2 : following voith parameter not showing in mcr alarm monitor panel: ( a ) control oil pressure, ( b ) lub oil pressure, ( c ) rotor oil pressure, ( d ) bearing oil temperature. to be rectified. 133 safety device checks to be undertaken on both the voith system 134 air starting motor of port main engine defective, to be repaired with oem listed spares as required . 135 valves of various systems : removal, overhauling, pressure testing and fitment of following system valves: ( a ) 65 mm sdnr valve 136 ( b ) 65 mm sd valve 137 ( c ) 80 mm gate valve 138 ( d ) 80mm globe valve 139 ( e ) 125 mm strom valve 140 ( f ) 150 mm sdnr valve 141 ( g ) 200 mm gate valve 142 ( h ) 200 mm butter fly valve 143 ( j ) 300 mm butter fly valve 144 ( k ) 100 mm gate valve 145 ( l ) 40 mm sdnr valve 146 ( m ) 40 mm globe sd valve 147 ( n ) 40 mm sd valve 148 ( o ) 32 mm sd valve 149 ( p ) 15 mm sdnr valve 150 ( q ) 65 mm strom valve 151 ( r ) 80 mm strom valve 152 ( s ) 125 mm sdnr valve 153 ( t ) 50 mm quick shut down valve 154 ( u ) 50 mm sdnr valve 155 ( v ) 20 mm sdnr valve 156 ( w ) 25 mm quick shut down valve 157 ( x ) 15 mm cock valve 158 remove, dismantle, chemically clean, assemble and pressure test to required pressure with spares for the following n ( a ) lub oil heat exchangers of both main engine n ( b ) both alfa cooler to be insitu dismantled, nmechanically cleaned and boxed back with new gaskets. system to be pressure tested and proved for operation post fitment of coolers. test pr 3.5 kg / cm2. n ( c ) existing inlet and outlet pipe of both alfa coolers to be repaced with cu ni pipe. length 0.3 mtr, mat ss, dia 80 mm n ( d ) sea water inlet pressure guage line adaptor of both alfa cooler damaged, to be renewed note quote for services and material / spares 159 renewal of hot lagging for da and main engine compartment note quote for services and material / spares 160 temperature gauges of various system lines to be renewed. note quote for services and material / spares 161 suction and discharge pressure gauges of various system lines to be renewed. note quote for services and material / spares 162 overhauling of fire hydrants to be carried out.note quote for services and material / spares 163 leakage observed from dirty oil pipe flange. brazing and pressure test to be carried out. mat cu ni, dia 50 mm. note quote for services and material / spares 164 leakage observed from fuel filling line in engine room. pipe to be replaced. dia 50 mm. lenght 0.5mtr, mat ms.note quote for services and material / spares 165 port main engine breather line cracked. pipe to be renewed. mat ms, dia 85 mm, length 0.5 mtr.note quote for services and material / spares 166 both da lub oil temperature increasing. both lub oil cooler to be cleaned and pressure tested.note quote for services and material / spares 167 both da sea water pressure line perished. line to be replaced. dia 5 mm. lenght 10 mtr, mat copper. note quote for services and material / spares 168 port main engine speed sensor no st173 and temperature sensor is not operational. sensors to be replaced with new sensor. note quote for services and material / spares 169 lub oil leakage observed from turbo charger return line. defect to be rectified. 170 fuel centrifugal filter of main engine defective. fuel centrifugal to be replaced. note quote for services and material / spares 171 air and co2 bottles to be pressure tested at 1.5 times of working pressure. 172 electrical dl:clean winding and ventilation ducts. check condition of winding insulation including end connections and renew windings if insulation values below 1 m ohm. check stator connection for good contact, retighten screws. replace earthing terminals. carry out the complete overhaulling of excitation panel and replace spares required for factory designed performance. check for healthiness of avr. avr tuning to be undertaken by vendor if required based on trial / performance reports. vendor to also cater for avr replacement if required. load trials to prove performance of alternator to be undertaken by the vendor. requisite load bank also to be arranged by the vendor. quote for services and spares. 173 navigation control panel to be overhauled and repair of defective lamps to be undertaken . note quote for services and material / spares 174 repair of mb sre amplifier unit to be carried out 175 emergency lights with assembly in various locations defective. to be replaced with new lights. quote for services and spares. n 176 fifi monitor remote operation non ops. suspected cable damaged. cable to be replaced and rotary switch to be renewed. cable specifications : 1 sq mm, 2 core. note quote for services and material / spares 177 carry out sr routines of all transformers fitted onboard with oem recommended components as required: ( a ) using a soft brush and vacuum cleaner, clean and blow out dust nand dirt from the terminal insulation block, between lamination and nthe side and bottom ventilation grills. n ( b ) check tightness of all connections and earth bonding straps. tight loose connections. n ( c ) check all lamination securing nuts for tightness. tight loose nuts. n ( d ) examine condition of insulation and cable spills for sign of ncracking and over heating. change low insulations / damaged cable. n ( e ) grease threads of cover securing nuts and bolts using anti seize ngrease and replace covers. n ( f ) examine shock / vibration mountings, renew if required. n ( g ) clean out using soft brush and blower. n ( h ) check all connections and terminal screws are tight. n ( i ) examine all wiring for signs of deterioration. renewed defective n ( j ) examine components for over heating / cracking and capacitors nfor leakage. renewed defective parts. n ( k ) revarnishing of the coils to be undertaken post routines n n 178 motors & starters: carry out overhauling of following motors and starters ( including remote operation ) . motor bearings to be replaced and trials to be offered to ship staff. rewinding of the motors to be undertaken if insulation values below 1 m ohm. replacement of ber / aber motors to be undertaken as one to one replacement. vendor to also cater for dismantling and refitment of the motor. equipment performance to be restored to factory designed condition. replacement of all defective parts to be catered by the vendor. note quote for services and material / spares ( a ) fire & gs p / p ( 7.5kw ) 179 ( b ) bilge ballast gs pp ( 11kw ) 180 ( c ) fo transfer pump ( 0.75kw ) 181 ( d ) lo transfer pp ( 0.75kw ) 182 ( e ) e / room supply fan ( 7.5kw ) 183 ( f ) dirty oil pp ( 0.75kw ) 184 ( g ) lub oil cetrifuge ( 0.75kw ) 185 ( h ) voith cooling pp ( 3.7kw ) 186 ( j ) windlass motor ( 5.6kw ) 187 ( k ) capstan motor ( 7.5kw ) 188 ( l ) o / bilge water seperator ( 0.55kw ) 189 ( m ) boat davit ( 7.5kw ) 190 lighting circuit cable and switches ( 30 nos ) at various locations perished / damaged. cable / switch renewal to be undertaken. cable specifications 2.5 sq mm, 2 core. 191 rewinding of 10kva lighting transformers view low insulation of primary and secondary windings. note quote for services and material / spares 192 sart battery to be replaced and instruments to be tested on board. battery specification 12 v, 7 ah. note quote for services and material / spares 193 renewal of 08 in no. mob fitted on weather deck, type lsa code msc 207 ( 81 ) . note quote for services and material / spares 194 repair of navigational lights fitted on main mast qty 04 . note quote for services and material / spares 195 replacement of test equipments: multimeter make fluke. 196 tong tester . make fluke. 197 analog megger. make fluke. 198 replacement of battery and hrg ( hydrostatic release gear ) of epirb. battery specs 12 v, 7 ah.note quote for services and material / spares 199 echo sounder calibration including fitting of hull appendages to be undertaken. printer fitted in wheel house defective. to be replaced. note quote for services and material / spares 200 e / r alarm panel display monitor not working. to be replaced. 201 split ac fitted in wheel house defective. to be repaired. note quote for services and material / spares 202 control batteries of da to be replaced. 12 v 120 ah 203 control batteries of da to be replaced . 12 v 150 ah 204 control batteries of da to be replaced . 12 v 180 ah 205 control batteries of da to be replaced . 12 v 200 ah 206 tank content gauges ( nivo system ) not working. functional checks all gauges to be carried out. defective components and sensors to be replaced. tank level calibration to be undertaken thereafter. display module serviceability checks and calibration to be undertaken. replace if ber / defective. quote for services 207 tubelight fitted onboard at various locations to be replaced with led tubelights . note quote for services and material / spares 208 serviceability of magnetic compass and anemometer to be undertaken followed by calibration with spares. renew if defective. qoute for services and spares 209 air whistle not working. overhauling and repair to be undertaken with oem recommended components as required. quote for services and spares 210 e / r general calling alarm not working. to be repaired 211 spt fitted onboard at various locations found defective, to be replaced. 212 window wiper and associated mechanisms and clear view in wheel house defective. to be renewed including spares. quote for services and spares. 213 e / r alarm panel display key board in wheel house not working. to be repaired with oem recommended components as required. 214 03 in no flood light and 02 in no search light not working. to be replaced. note quote for services and material / spares 215 port main engine emergency stop push button is defective at the wheel house. to be replaced with new one. 216 renewal of flood lights fitted in engine room with led lights. note quote for services and material / spares 217 double pole switch with single way are defective. to be replaced with new one. note quote for services and material / spares 218 deck lights guard / fitting are broken. to be replaced with new one. note quote for services and material / spares 219 repair gps display unit garmin with oem recommended components as required and undertake serviceability checks. note quote for services and material / spares 220 tru batteries not holding charge. to be replaced with new one 12v 180 ah maintenance free batteries . note quote for services and material / spares 221 following defective. to be repaired / replaced n ( a ) wall mounted fan defective ( 20 nos ) . n ( b ) galley hot plate ( 02 nos ) 222 5kva ups defective. batteries to be renewed. battery specification 12 v, 150 ah ( 2 nos ) 223 deck washing machine non opertional to be renewed. note quote for services and material / spares 224 lighting switches are broken at various locations. to be replaced with holder assembly. note quote for services and material / spares 225 serviceability checks of navigational radar including vswr and power output checks. replace defective transreceiver pcb and other components as necessary. qoute for services and spares. 226 hull spares: capstan fixed contacts. ( ser no. 18 ) 227 moving contacts ( ser no. 213 ) 228 indicating lamps ( red ) . ( ser no. 210 ) 229 fuse links ( ser no. 206 ) 230 controller contacts ( fixed ) ( ser no. 190 ) 231 controller contacts ( moved ) ( ser no. 190 ) 232 friction lining for disc brake ( ser no. 14 ) 233 boat davit limit switch ( ser no. 31 ) 234 fuse elements ( 2a, 4a, 32a ) ( ser no. 200 ) 235 indicating lamps ( red ) ( ser no. 206 ) 236 push button ( green ) ( ser no. 206 ) 237 liner for brake ( ser no. 25 ) 238 fuse for ( 1a, 2a, 4a, 10a, 16a, 32a ) ( ser no. 178 ) 239 master controller contact kits ( ser no. 177 ) 240 contractor kits ( ser no. 174 ) 241 lamps ( ser no. 173 ) 242 bearing for motor ( ser no. 179 ) 243 friction liner for disc brake ( ser no. 14 ) 244 gland packing, walker remix ( p.no.bba2522 879 ) ( ser no. 26 ) 245 indication lamps ( ser no. 21 ) 246 mp filter hp0372a10an, italy ( p. no. hp0372a10an ) ( ser no. 24 ) 247 washer od 100x1d 80 ( ser no. 24 ) 248 main engine, wartsilla, model : 8l 26 spares : fuel filter ( 4761002 ) ( ser no. 82 & 158 ) 249 filter paper ( 4713047 ) ( ser no. 82 & 158 ) 250 gasket ( 1072002 ) ( ser no. 82 & 158 ) 251 gasket ( 1072003 ) ( ser no. 82 & 158 ) 252 o ring 20x3 ( 121007 ) ( ser no. 82 & 158 ) 253 o ring ( 4712063 ) ( ser no. 82 & 158 ) 254 gasket ( 4712062 ) ( ser no. 82 & 158 ) 255 screw ( 218003 ) ( ser no. 82 & 158 ) 256 valve ( 2180049 ) ( ser no. 82 & 158 ) 257 o ring ( 2180059 ) ( ser no. 82 & 158 ) 258 starting air pipe ( 2180063 ) ( ser no. 82 & 158 ) 259 sealing ring ( 2180076 ) ( ser no. 82 & 158 ) 260 o ring ( 2180077 ) ( ser no. 82 & 158 ) 261 washer ( 2180085 ) ( ser no. 82 & 158 ) 262 gasket ( 2180086 ) ( ser no. 82 & 158 ) 263 following spares main diesel alternator model:6cta8.3d / m ( mandatory spares ) : element lub oil ( lube oil filter ) make : fleetguard ( 3401544 ) ( ser no. 83 ) 264 ring compress ( 3919918 ) ( ser no. 83 ) 265 ring compress ( 3922686 ) ( ser no. 83 ) 266 ring retainer ( 3920692 ) ( ser no. 83 ) 267 ring, oil piston ( 3921919 ) ( ser no. 83 ) 268 regulator, vol. stamford mx321, eoo 23212 ( 2890759 ) ( ser no. 83 ) 269 rectifier ( 2890014 ) ( ser no. 83 ) 270 bearing, main ( thrust ) ( 3944153 ) ( ser no. 83 ) 271 bearing, main ( thrust ) ( 3944158 ) ( ser no. 83 ) 272 bearing crank ( thrust ) ( 3944163 ) ( ser no. 83 ) 273 valve, intake ( 3924492 ) ( ser no. 83 ) 274 valve, intake ( 3921444 ) ( ser no. 83 ) 275 collet, valve ( 3901177 ) ( ser no. 83 ) 276 guide, valve ( 3925863 ) ( ser no. 83 ) 277 injector ( 3926787 ) ( ser no. 83 ) 278 valve spring ( 3991085 ) ( ser no. 83 ) 279 gasket, exh. ou; ( 3873509 ) ( ser no. 83 ) 280 valve insert ( 3970278 ) ( ser no. 83 ) 281 bearing connection ( 3901430 ) ( ser no. 83 ) 282 piston pin ( 3934046 ) ( ser no. 83 ) 283 fuel filter ( 3931063 ) ( ser no. 83 ) 284 valve insert ( 3908830 ) ( ser no. 83 ) 285 element air cleaner ( 3814313 ) ( ser no. 83 ) 286 element air cleaner ( 3814312 ) ( ser no. 83 ) 287 gasket set ( gasket turbo ) ( 3755843 ) ( ser no. 83 ) 288 belt v ribbed ( 3289124 ) ( ser no. 83 ) 289 seal, valve st ( 3927642 ) ( ser no. 83 ) 290 bolt, connection ( 3928870 ) ( ser no. 83 ) 291 nut connection ( 3934864 ) ( ser no. 83 ) 292 pump fuel injector ( 5263870 ) ( ser no. 83 ) 293 tube injector ( 5271935 ) ( ser no. 83 ) 294 sensors, pr. ( 2 to 10 bar ) ( 4911882 ) ( ser no. 83 ) 295 sensors ( temperature ) ( 4911877 ) ( ser no. 83 ) 296 pump, sea water ( 4963510 ) ( ser no. 83 ) 297 seal oil ( 3942535 ) ( ser no. 83 ) 298 seal oil ( 5259499 ) ( ser no. 83 ) 299 seal injector ( 3909886 ) ( ser no. 83 ) 300 gasket exhaust ( 3932063 ) ( ser no. 83 ) 301 gasket gear , h ( 3944293 ) ( ser no. 83 ) 302 gasket cover ( 3939258 ) ( ser no. 83 ) 303 gasket hydraulic ( 3940245 ) ( ser no. 83 ) 304 gasket cylinder ( 3938267 ) ( ser no. 83 ) 305 washers lock ( 611 ) ( ser no. 83 ) 306 screw hex, flange ( 3243948 ) ( ser no. 83 ) 307 plug pipe ( s911b ) ( ser no. 83 ) 308 hardness wiring ( 3875359 ) ( ser no. 83 ) 309 control governor ( 3974704 ) ( ser no. 83 ) 310 washer plain ( 640 ) ( ser no. 83 ) 311 nut heavy hex ( 204 ) ( ser no. 83 ) 312 screw haxagon ( 112c ) ( ser no. 83 ) 313 washers plain ( s602 ) ( ser no. 83 ) 314 washers lock ( 604 ) ( ser no. 83 ) 315 clamp hose ( 43828 ) ( ser no. 83 ) 316 brace, tube ( 101470 ) ( ser no. 83 ) 317 clip ( 107460 ) ( ser no. 83 ) 318 screw hexagon ( 109 ) ( ser no. 83 ) 319 connection ex ( 3814793 ) ( ser no. 83 ) 320 flange, weld ( 3226087 ) ( ser no. 83 ) 321 clip ( 500694 ) ( ser no. 83 ) 322 screw hexagon 112c ) ( ser no. 83 ) 323 screw hexagon ( 1137 ) ( ser no. 83 ) 324 nut hex heavy ( 204 ) ( ser no. 83 ) 325 nut hex heavy ( 203 ) ( ser no. 83 ) 326 washers lock ( 604 ) ( ser no. 83 ) 327 washers lock ( 611 ) ( ser no. 83 ) 328 washers plain ( 640 ) ( ser no. 83 ) 329 gasket exhaust ou 2880039 ) ( ser no. 83 ) 330 gasket dia 135 pcd 115 dia ( 3940245 ) ( ser no. 83 ) 331 washer plain ( 640 ) ( ser no. 83 ) 332 connection se ( 2867840 ) ( ser no. 83 ) 333 connection se ( 2867838 ) ( ser no. 83 ) 334 tools : ½ breaker bar 15’’ long ( ser no. 83 ) 335 procurement of following spares of voith turbo schneider propulsion type vsp 28r5 / 234 2ae45 kw rpm ( mandatory spares ) : shaft seal ring adck 300x340x16 ( h01.067195 ) ( ser no. 84 ) 336 round cord ring v 420x4.5nbr70 ( h01.086366 ) ( ser no. 84 ) 337 o ring 560x5 nbr70 ( h01.032840 ) ( ser no. 84 ) 338 o ring 454x8 nbr 70 ( h01.064102 ) ( ser no. 84 ) 339 bulb lamp 35x18.5 24v 5w ( h01.095322 ) ( ser no. 84 ) 340 filter element hydac 12782361300r020 ( h01.016221 ) ( ser no. 84 ) 341 repair kit ( h01.012435 ) ( ser no. 84 ) 342 alfa laval fuel oil centrifuge: major service kit 546670 07 08 343 ows make suyash, modle sd0.5: cover gasket ( 8320025002 ) ( ser no 86 ) 344 coaleser element ( 2704002501 ) ( ser no 86 ) 345 sacrificial anode ( 6453020001 ) ( ser no 86 ) 346 set stuffing box packing ( 546040207ep1 ) ( ser no 86 ) 347 desicator cartridge ( 51110em027 ) ( ser no 86 ) 348 reciprocating air compressors make elgi ( model hp 10 300 ) : v belt ( 000905283 ) ( ser no 87 ) 349 inlet air filter ( 022100929 ) ( ser no 87 ) 350 gasket free end civer ( 020365450 ) ( ser no 87 ) 351 gasket fly end ( 000425510 ) ( ser no 87 ) 352 gasket valve flate ( 000411530 ) ( ser no 87 ) 353 valve finger type ( 0003300950 ) ( ser no 87 ) 354 valve finger type ( 000330970 ) ( ser no 87 ) 355 gasket ( 0001004a ) ( ser no 87 ) 356 anchor windlass: packing for top cover ( 02211 6235 1015 ) ( ser no. 19 ) 357 friction lining for slipping clutch ( 02 18 6232 sc 875240 ) ( ser no. 19 ) 358 spring for slipping clutch ( 02 18 6232 sc 875270 ) ( ser no. 19 ) 359 rivets for friction lining ( 02 18 6232 sc 875 ) ( ser no. 19 ) 360 friction lining for emb ( b emb 2451 b 3024 ) ( ser no. 19 ) 361 rivets for friction lining ( a emb 1900 180 3092 ) ( ser no. 19 ) 362 spring for emb ( b emb 2451 b 3017 ) ( ser no. 19 ) 363 procurement of following maintenance free lead acid batteries ( a ) 120 ah 12 nos ( ser no. 19 ) 364 ( b ) 150 ah 12 nos ( ser no. 19 ) 365 ( c ) 180 ah 12 nos ( ser no. 19 ) 366 ( d ) 200 ah 10 nos ( ser no. 19 ) 367 fuse ( 0219 6232 9000 f1 f10 ) ( ser no. 19 ) 368 indication lamp ( 02 19 6232 9000 h1 h2 ) ( ser no. 19 ) 369 service charge for third party inspection ( for hull survey and qc ) ...

Karnataka Power Transmission Corporation Limited - Karnataka

22165591 1.design fabrication galvanizing and supply of mild tensile 66kv dc type b+6 meter extension tower including stubs weight as per kalpatharu design. 2. supply of galvanized bolts, nuts as per kalpatharu design and various tower accessories and miscellaneous materials etc. 3.supply of disc insulators, tension clamps, double tension, single tension clamps, pg clamps vibration dampers for coyote acsr , ground conductor 7/3.15mm msc joint for coyote acsr ground conductor 4.grounding towers with cost of 40mm dia 2.5mm thick c class pipe 3mts long with 50x6mm gi flat 3mtr long salt charcoal. 5.check survey, pit marking and sorting of tower parts , setting of stubs, templates, aligning , dismantling and transportation of template from one location to another location. 6.assembling and erection of towers including tightening of bolts , nuts including loading and un loading at stores , welding of bolts nuts. 7.releasing and restringing of coyote ground conductors from t1 to t10. 8.civil works including excavation for b+6m nbt tower in dry fissured rock, dry fissured rock without blasting. backfilling with excavated soil available near the tower and consolidation layer by layer , supply providing tmt steel reinforcement cutting, bending, hooking , placing in position, lapping. concreting and curing for transmission line towers, 9. dismantling of s/c 66kv a+6 type normal tower excluding stubs and bolts nuts along with loading unloading of released tower.=> open...

Indian Navy - Karnataka

20723990 tender for undertaking 6000 hrly routines on main engines => single: 1.01 remove and check rocker arms ( push rod driven ) and valve bridges for wear. check rocker arms ( cam shaft driven ) and rocker bearings for wear. 1.02 remove cylinder heads. check inlet valve guides, replace exhaust valve guides. condition valves and valve seats.replace o rings on the protective seals. replace gaskets. 1.03 check cylinder liner wear pattern. 1.04 remove and inspect vibration damper, recondition if necessary. 1.05 remove, disassemble, clean, check components of exhaust turbocharger, measure bearing clearances and compressor wheels. 1.06 clean air ducts / pipes and renew sealing components. 1.07 clean intercooler and test for leaks. replace sealing materials on all disassembled components. 1.08 check function of sequential control valve. 1.09 replace / renewal fuel injectors 1.1 replace high pressure fuel sensor 1.11 overhaul engine coolant pump. 1.12 overhaul raw water pump. 1.13 clean engine coolant cooler and pressure test for leaks 1.14 calibrate engine coolant thermostat, replace if required. 1.15 clean engine oil heat exchanger and check for leaks. replace sealing material on all disassembled components. 1.16 overhaul air starting motor 1.17 check sv mounts for condition, securing and, tightness. measure adjustment dimension on central buffer of engine mounts. 1.18 renew sv mounts 1.19 check centrifugal oil filter bearings. replace if necessary 2 spares 2 2.01 o ring 2.02 o ring 2.03 o ring 2.04 sealing ring 2.05 o ring 2.06 o ring 2.07 o ring 2.08 clamp 2.09 sealing ring 2.1 sealing ring 2.11 gasket 2.12 o ring 2.13 o ring 2.14 sealing ring 2.15 vent plug 2.16 sealing ring 2.17 stud 2.18 hexagonal nut 2.19 o ring 2.2 piston ring 2.21 screw 2.22 piston ring 2.23 hex nut 2.24 o ring 2.25 sealing ring 2.26 washer 2.27 washer 2.28 sealing strip 2.29 o ring 2.3 gasket 2.31 screw 2.32 washer 2.33 sealing ring 2.34 o ring...

Indian Navy - Karnataka

17185756 tender for short refit work package affected area approx 200 sqmtr , both ballast tank to be cleaned throughly, to be inspected for corrossion. if the area up to 30 % tank to be power tooled. if the affected area above 30% the area to beblasted and paint scheme to be restored. fwd ballast tank area 320 sqmtrs , aft ballast tank area 240 sqmtrs , both fresh water tank to be cleaned throughtly , to be inspected for corrossion. if the area up to 30 % tank to be power tooled. if the affected area above 30% the area to be blasted and paint scheme to be restored.tank area 80 sqmtr each , both chain locker, void space to be cleaned affected area to be power tooled to st 3 and paint to be restored. approx area 14 sqmtr ,both fuel oil storage tank and two ru tank to be cleaned throughtly , to be inspected for corrossion. entire area of tank to be power tooled. oil smearing before boxing up .tank area 400 sqmtr, superstructu re area including mast and funnel to be hp jet washed, paint damaged area to be power tooled to st.3 and paint to be applied as per paint scheme. approx area 280 ,engine room internal bulkhead to be cleaned by fresh water moping, damaged area to be power tooled and paint to be restored and one final coat on entire area to be applied including system pipes. after painting colour coding of system pipe to be restored. approx area 1200 sqmtr, main engines (makecaterpillar, model 3512c, qty 02) carry out yearly or 2000 hourly routines mentioned prove them for satisfactory performance (a) cooling system coolant sample(level 2) check (b) undertake complete checks/provin g of engine controls and instrumentatio n including safety device if not done during the year as part of 250 hourly routine, rectify any defects found (c) clean air starting motor lubricating bowl (d) inspect crankshaft vibration damper ...