40551317
tender for comprehensive maintenance of married accn at air force station sambra 1 demolition of cement concrete ( unreinforced ) of any description and in any position not otherwise specifically provided for, complete all as specified & directed. 2 demolition of cement concrete ( unreinforced ) in ground floors and pavings not exceeding 15cm thickness ( below or above ground level ) , completeallas specified & directed. 3 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) of any thickness and in any positionand removing serviceable tiles to store and rubbish off the premises completeall as specified & directed. 4 dismantling and breaking up drain pipes ( salt glazed ware, ac, reinforced concrete, pvc or cast iron ) set in cement mortar of size 100mm / 75mmfixed over wall or in floor including clamps etc., completeallas specified & directed. 5 dismantling of brickwork, concrete masony workor stone / boulder masonry work, built in cement mortar including allquoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles completeall as specified & directed. 6 taking down cement rendering / plastering of any thickness and of any description including raking out joints, hacking for key, scrubbing down with water etc., over wall or ceiling surfaces completeallas specified & directed. 7 taking up or down 15mm bore dia, mild steel or of any material water tubing and fittings / connections etc., fixed over wall or in floor including necessary cutting / chasing and making good in cement mortar 1:4 completeallas specified & directed. 8 taking up or down 20mm bore dia, mild steel or of any material water tubing and fittings / connections etc., fixed over wall or in floor including necessary cutting / chasing and making good in cement mortar 1:4 completeallas specified & directed. 9 taking up or down 25mm bore dia, mild steel or of any material water tubing and fittings / connections etc., fixed over wall or in floor including necessary cutting / chasing and making good in cement mortar 1:4 completeallas specified & directed. 10 taking down chowkhats or frames not exceeding 1.5 sqm each with shutters ( without taking off shutters from the frames ) including hold fasts from wall and making good in cement mortar 1:4 completeallas specified & directed. 11 taking down chowkhats or frames exceeding 1.5 sqm each but not exceeding 4sqm each with shutters ( without taking off shutters from the frames ) including hold fasts from wall and making good in cement mortar 1:4 completeallas specified & directed. 12 taking down shutter of any description and material exceding 1.00 sqm but not exceeding 2.00 sqm each completeallas specified & directed. 13 supply and fix in repair bib tap fancy type 15mm bore dia, long bodychromium plated cast copper alloy, screwed down, high pressure, screwed ends for water pipe fitting or for unions including cp finish cup washer / wall flange completeallas specified & directed. 14 supply and fix in repair bib tap fancy type 15mm bore dia, short bodychromium plated cast copper alloy, screwed down, high pressure, screwed ends for water pipe fitting or for unions including cp finish cup washer / wall flange completeallas specified & directed. 15 supply and fix in repair angle stop valve, 15mm bore dia fancy typechromium plated, cast copper alloy, screwed down, high pressure, screwed ends for water pipe fitting or for unions including cp finish cup washer / wall flange completeallas specified & directed. 16 supply and fix pvc connection 15mm size with ptmt nuts of length 450mm completeallas specified & directed. 17 supply and fix pvc connection 15mm size with ptmt nuts of length 600mm completeallas specified & directed. 18 supply and fixin repairflushing cistern, dual flush, low level, white, 10 liter capacity pvc valveless, syphonic action type, with inlet, ball valve, float, and handle / push type, including 32mm bore dia pvc long / short flusing pipe andbrackets complete in all respect as specified & directed. 19 supply and fix in repairs swivel shower , stainless steel, fancy type square shape of minimum size 100mmx100mm including cp finish shower rod ( long ) and cup washer / wall flange for fixing with 15mm bore dia pipe / fittings completeallas specified & directed. 20 supply and fix stainless steel gratings 150x150mm size with openable circular grating with or without waste hole including necessary cutting and make good of floor complete allas specified & directed. 21 supply and fixin repairs tubular brass chromium plated towel rail 20mm dia d type 60cm long between flanges completeallas specified & directed. 22 supply and fix in repairsoap dishstainless steelfixed to plugs complete in all respect as specified & directed. 23 supply and fix in repair, wall mixer cast copper alloy chromium plated, 15mm bore dia, mixing hot & cold water screwed down for water pipe / fittings completeallas specified & directed. 24 s & f in repairs vitreous china wash hand basin, white in colour, flat back of size 550x400mm x200mm including pedestal, and 32mm bore dia cp finish cast copper alloy waste fitting / coupling, 32mm bore dia pvc waste pipe including cutting for and pinning in ends of brackets or erecting stand brackets completeallas specified & directed. make : cera cat part no. s2040157 and s2090101 or jaquar cat part no. ecs wht 801 & ecs wht 301 or equivalent make in parryware / hindware 25 supply and fix wall mounted sheet glass shelf assembly consisting of acrylic sheet shelf 12cm wide with chromium plated bracket guard and railing 60cm long completeallas specified & directed. 26 supply and fix wall mounted sheet glass corner shelf assembly consisting of acrylic sheet shelf 20cm wide and 30cm long each side with chromium plated bracket guard and railing, completeallas specified & directed. 27 taking down shutter of any description and material from frame / chowkhat exceeding 1sqm but not exceeding 3 sqm each and re fix in the same opening after necessary repairing, ease and adjust, cutting, grinding, adjusting, including using new nails / screws complete in all respect as specified and directed. note: material required other than mentioned in this item for repairing shall be paid under respective supply only item. 28 taking down shutter of any description and material from frame / chowkhat not exceeding 1sqm each and re fix in the same opening after necessary repairing, ease and adjust, cutting, grinding, adjusting, including using new nails / screws complete in all respect as specified and directed. note: material required other than mentioned in this item for repairing shall be paid under respective supply only item. 29 s & f in repair stainless steel wire cloth 0.36mm dia of wire and average width of aperature 1.40mm and fixed in wooden door / window shutters including new second class hard wood beading of required size to secure the wire cloth / mesh completeallas specified and directed. 30 supply and fix 4mm thick sheet glass, ordinary quality, in squares, pane including taking down from wooden shutter of any description including using necessary size of second class hard wood beading to secure the glasss completeallas specified and directed. 31 supply and fix 4mm thick figured glass, ordinary quality, in squares, including taking down from wooden shutter of any description including necessary size of second class hard wood beading to secure the glasss completeallas specified and directed. 32 supply and fix 4mm thick sheet glass, ordinary quality, in squares, including taking down from steel shutter of any description including necessary glass putty and glass pins to secure the glasss completeallas specified and directed. 33 supply and fix 4mm thick figured glass, ordinary quality, in squares, including taking down from steel shutter of any description including necessary glass putty and glass pins to secure the glasss completeallas specified and directed. 34 material, labour, t & p required for welding on site of steel window / gate or hinges or similar work to steel sections of any description, thickness of weld exceeding 6mm but not exceeding 9mm including taking out of unserviceable material, easing to shutter, grinding, sanding complete to make usable and openable complete in all respect as specified and directed. 35 supply onlybutt hinges 100mm medium weight mild steel cold rolled mild steel allas specified and directed. 36 supply only butt hinges 100mm medium weight stainless steelincluding necessary stainless steel screws of required size allas specified and directed. 37 supply onlybutt hinges 75mm medium weight mild steel cold rolled mild steel allas specified and directed. 38 supply onlyhinges box type / projected type for steel window / ventilator or similar description allas specified and directed. 39 supply and fixed anodised aluminium handle 125mm long, cast type type completeallas specified & directed. 40 supply and fixed anodised aluminium handle 150mm long, cast type type completeallas specified & directed. 41 supply and fix aluminium anodised hasp and staple 100mm long, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screwscompleteallas specified & directed. 42 supply and fix floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece completeallas specified & directed. 43 supply onlyanodised aluminium handle 125mm long cast type completeallas specified & directed. 44 supply onlyanodised aluminium handle 150mm long cast type complete allas specified & directed. 45 supply only aluminium anodised hasp and staple, safety type, 100mm longwith mild steel hinge pin including bolt to hinge plate and fixed with screwscomplete allas specified & directed. 46 supply only floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece completeallas specified & directed. 47 supply and fix in repair aluminium alloy, anodised, sliding door bolt 250mm long, with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed completeallas specified & directed. 48 supply and fix in repairaluminium, anodised barrel tower bolts of extruded section 200mm long completeallas specified & directed. 49 supply onlyaluminium alloy, anodised, sliding door bolt250mm long, with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed completeallas specified & directed. 50 supply onlyaluminium anodised barrel tower bolts of extruded section, 200mm long, complete all as specified & directed. 51 s & f factory made single extruded wpc ( wood polymer composite ) solid one side decorated and other side plain flush door shutter of 30mm thick comprising of virgin polymer of k value 58 60 ( suspension grade ) , calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) having minimum density of 650 kg / cum and screw withdrawal strength of 1800 n ( face ) & 900 n ( edge ) , minimum compressive strength 50 n / mm2, modulus of elasticity 850 n / mm2 and resistance to spread of flame of class a category with property of being termite / borer proof, water / moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk s.s screws, all as directed. note: stainless steel butt hinges and necessary s s screws shall be paid separately ) complete all as specified & directed. 52 s & f pvc celuka ply / board 17 18mm thick, one side prelam / rigidlam and other side plain colour fixed with screws, solvent cement / adhesive to make cup board / cabinet shutters / drawer front / sides, partitions, shelves etc. including 1mm thick pvc lipping / beading fixed with solvet over edges of ply of required width and colour complete all as specified and directed. 53 s & fsleek soft hydraulic auto closing 3d ( big bend / middle bend / straight arm type ) stainless steel finish hinges openable of 0 or 15 degree crank for cup board / cabinet shutters ( sample available in ge office ) complete all as specified and directed. note : auto closing shall be all as per sample kept in ges office 54 supplying and fixing cpvc pipes sdr 11, 15mm nominal size including plain & brass threaded special fittings of same size or of reducer or enlarged size, fixed to wall / ceiling or laying in floors and necessary cutting / chases in wall / floor of any description and their making good completeallas specified and directed. 55 supplying and fixing cpvc pipes sdr 11, 20mm nominal size including plain & brass threaded special fittings of same size or of reducer or enlarged size, fixed to wall / ceiling or laying in floors and necessary cutting / chases in wall / floor of any description and their making good completeallas specified and directed. 56 supplying and fixingcpvc pipes sdr 11, 25mm nominal sizeincluding plain & brass threaded special fittings of same size or of reducer or enlarged size, fixed to wall / ceiling or laying in floors and necessary cutting / chases in wall / floor of any description and their making good completeallas specified and directed. 57 supply and fixinggalvanised iron tubing 25mm bore dia tubes, medium grade, with all fittings of same size or of reducer or enlarged bore dia fixed to walls / ceiling or laying in floors including necessary cutting / chases in wall / floor of any description and their making good completeallas specified & directed. 58 supply and fixingfactory made wire mesh solid wpc door shutter30mm thick consisting of density 650 kg / cbm manufactured by an iso 9001 2015 certified company, door to be panelled with ss mosquito mesh and xtn aluminium mesh for additional strength and safety purpose. ( confirming as per is:4020 ) . the door should be water proof, termite proof, fire retardant and having screw holding capacity. door to be fixed to frame with 3 nos. m.s powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws.other hardwares should be fixed with 19x6mm size steel screws etc. complete as per manufacturers specification & directed 59 s & f in repairsblock boards 18 19mm thickgrade 2 quality, interior grade, commercial type, fixed to timber frame work as in cup board / almirah shelves or similar type of works including second class hard wood beading / margin / leeping alround the edge of the board completeallas specified & directed. 60 supply and fix bath room mirror cabinet of size 450mmx350mm, high grade plastic, 3mm thick looking mirrorfixed to wooden / pvc plugs with screws complete in all respect as specified & directed. 61 supply and fix in repair bevelled edge mirror of selected quality glass, 600 mm x 450 mm size mounted on 6 mm thick asbestos cement building board or commercial plywood and fixed to wooden plugs with chromium plated screws and washer complete in all respect as specified & directed. 62 supply and fix in repairs toilet paper holder with flat recessed type stainless steel material completeallas specified & directed. 63 supply and fix in repairs vitreous chinawash down water closet pan, pedestal patternwhite ( excluding flushing cistern ) including plastic water closet seat, white closed pattern with flat bottom and cover and mild steel chromium plated hinging device completeallas specified & directed. 64 supply and fix in repairs vitreous china squatting pan, ‘orissa’ pattern, size 580 x 440 mm white, with integral foot rests ( excluding flushing cistern and flush pipe ) including necessary pcc bedding, p or s pvc trap connected to pvc / ci pipes completeallas specified and directed. 65 material and labour for cleaning and removing of all scale and dirt etc., from tanks, and from mouth of circulating pipes etc. including using 50gm of bleaching powder per tank after disconnecting of outlet pipe and re connecting in the same position, capacity of tank exc. 250 litres but not exc. 500 litres each and marked on tank with white synthetic enamel paint as tank cleaned on ________ using stencil completeallas specified and directed 66 material and labour for cleaning and removing of all scale and dirt etc., from tanks, and from mouth of circulating pipes etc. including using 70gm of bleaching powder per tank after disconnecting of outlet pipe and re connecting in the same position, capacity of tank exc. 500 litres but not exc. 1000 litres each and marked on tank with white synthetic enamel paint as tank cleaned on ________ using stencil complete in all respect as specified and directed by engineer in charge. 67 supply and fix pvc lid cover suitable for pvc water storage tank of 500 / 1000 liter capacity of any description and shape as per existing water storage tank including necessary locking facility completeallas specified and directed 68 supply and fix in repairs vitreous china half stall urinal of size 350x340x615mm bowl type ( back or corner wall type ) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in white cement; fixing to flushing cistern, flush pipe, 40mm bore dia cp finish cast copper alloy waste fitting completeallas specified and directed. 69 supply and fix in repairs 32 / 40mm dia pvc flexible waste pipe for wash hand basin, kitchen sink, urinal or similar work completeallas specified and directed. 70 supply and fix in repairs 32mm dia cp finish cast copper alloy waste fitting for wash hand basin, with long screwed shanks and fly nut and flange end, bedded in red lead cement complete in all respect as specified and directed. 71 supply and fix in repairs waste fitting for stainless steel kitchen sink, cast copper alloy chromium plated as per existing size and designs, with long screwed shanks and fly nut and flange end, bedded in red lead cement completeallas specified and directed. 72 material and labour pre cast cement concrete 1:3:6type c1 using 20mm nominal size crushed and graded stone aggregate as insolid block masonary, setting in cement mortar 1:4 having minimum compressive strength of 50 kg per sqcm completeallas specified & directed. 73 providing and laying cement concrete 1:2:4 type b 1, using 20mm graded crushed stone aggregate formud stops, roof kerbs, rounded or chamfered or similar items finished fair and even including necessary form work completeallas specified & directed. 74 providing and laying cement concrete 1:2:4 type b 0 using 12.5mm graded crushed stone aggregate as in 25mm thick for levelling / to receive screed for laying floor finish, finished fair and even completeallas specified & directed. 75 providing and laying cement concrete 1:2:4 type b 1 using 20mm graded crushed stone aggregate as in 75mm thick sub base of floors & pavings or similar work finished fair and even completeallas specified & directed. 76 providing and laying cement concrete 1:3:6 type c 1, using 20mm graded crushed stone aggregate as in75mm thick plinth protection including filling of expansion joint with bituminous mixture finished fair and even completeallas specified & directed. 77 providing and laying cement concrete 1:4:8type d 1, using 20mm graded crushed stone aggregate as in 75mm thick sub base to floors or of similar type of work finished fair and even completeallas specified & directed. 78 providing and laying for cement concrete 1:2:4 type b 1, using 20mm graded crushed stone aggregate as in coping, hold fast block orsimilar type of workincluding necessary form work completeallas specified & directed. 79 m & lriver sand filling under paver block / floors or in foundations including watering and consolidation completeallas specified & directed. 80 providing and laying precast concrete interlocking paver block, rubber moulded, 60mm thick machine pressed, of any shape and size confirming to is 15658 2006, m 35 grade of concrete with grey cement and pigment completeallas specified & directed. 81 m & l for coloured non skid ceramic tiles 6 7mm thick ( square / rectangular ) area of each tiles exceeding 0.08 sqm but not exc 0.16 sqm in floor, set and jointed in neat cement slury and pointed in white cement with pigment to match the shade of tiles over & including 15mm thick cement mortar 1:4 screed bed completeallas specified & directed. 82 m & lcoloured glazed ceramic tiles joint less / edge cutted of size 450x300x6 7mm thick as in vertical surfaces / dado, set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 10mm thick backing coat in cement mortar 1:4 completeallas specified & directed. note: quoted rate is deemed to be included the tiles fixed right angled to each other, the each tile should be chamfered / trim / sharp at 45 degrees at joint / corner / edge. 83 m & l double charged vitrified tiles 7 9mm thick ( square / rectangular ) polished, joint less / edge cut glazed / matt finish light shadearea of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchthe tile colour, set and jointed in neat cement slury over & includingscreed bed or bedding layer 15mm thick cement mortar 1:4 completeallas specified & directed. 84 m & l double charged vitrified tiles 7 9mm thick ( square / rectangular ) polished, joint less / edge cut glazed / matt finish light / dark shade, area of each tiles not exceeding 0.36 sqm, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchthe tile colour, over and including 10mm thick backing coat in cement mortar 1:4 completeallas specified & directed. note: the quoted rate is deemed to be includedthe tiles fixed right angled to each other the each tile should be chamfered / trim at 45 degrees at joint / corner / edge 85 m & l rendering 15mm thick cement mortar 1:6 over brick or concrete walls surface of any description, finished even & smooth without using extra cement completeallas specified & directed. 86 m & l rendering 15mm thick cement mortar 1:4 over brick or concrete walls surface of any description, finished even & smooth without using extra cement completeallas specified & directed. 87 m & l rendering 10mm thick cement mortar 1:3 over concrete ceiling surface of any description, finished even & smooth without using extra cement completeallas specified & directed. 88 supply and fix in repair vitreous china floor mounted pedestal pattern wash down water closet, curvy design d shaped bowl rimless one piece, white colour having pvc / cip or s type trap element, including following accessoreis complete in all respect as specified & directed.: ( a ) suitable seat cover ( b ) flexible pvc pipe 1.5m long and cp finish cast copper alloy 15mm bore dia health faucet, ( c ) pvc connection pipe 15mm bore dia 450mm long, ( d ) chromium plated cast copper alloy two way fancy bib cock 15mm bore dia make for water closet : cera cat part no. s1013217 andor jaquar cat part no. ecs wht 851s300sppsm or equivalent make in parryware / hindwarenote: the quoted rate is deemed to be included the joints between floor and wc shall be filled with silicon jel and stainless steel screws required for fixing 89 supply and fix in repair wash basin mixer 15mm bore dia fancy , cast copper alloy, chromium plated finish including necessary connecting pipe, screwed down, screwed for water pipe completeallas specified & directed. 90 supply and fix in repaircpvcr gate valves 25mm nominal dia bore connected with pipe with solventof any material complete all as specified & directed. 91 supply and fixpvc ( swr ) pipes 75mm bore dia, single socketed in any length with rubber ring joints, fixed to wall with necessary clamps complete , all , as specified & directed. 92 supply and fixpvc ( swr ) pipes 75mm bore dia single socketed in any length with rubber ring joints, laid in trenches or in floor completeallas specified & directed. 93 supply and fixpvc ( swr ) pipes110mm bore dia single socketed in any length with rubber ring joints, fixed to wall with necessary clamps completeallas specified & directed. 94 supply and fix pvc ( swr ) pipes 110mm diasingle socketed in any length with rubber ring joints, laid in trenches or in floor completeallas specified & directed. 95 supply and fix pvc ( swr ) floor trap of outlet dia 75mm with stainless steel gratings 150x150mm size with openable circular grating including jointing with solvent cement including fixing to pipe properly with solvent completeallas specified & directed. 96 supply and fix pvc ( swr ) bends with access door for 75 mm bore pipe completeallas specified & directed. 97 supply and fix pvc ( swr ) bends with access doorfor 110 mm bore pipe completeallas specified & directed. 98 supply and fix pvc ( swr ) junction single, ( single t ) equal or unequal size with access door for 75 mm bore pipe completeallas specified & directed. 99 supply and fix pvc ( swr ) junction single, ( single t ) equal or unequal with access door for 110mm bore pipe completeallas specified & directed. 100 supply and fix pvc ( swr ) vent cowl 110 mm dia completeallas specified & directed. 101 supply and fix pvc ( swr ) vent cowl 75 mm dia complete all as specified & directed. 102 dismantling of existing water storage tank and supply, hoisting and fixing of triple layer, isi marked, 1000 litre rotational moulded polyethylene water storage tank ( cylindrical vertical with closed top ) fixed in position all as specified in ssr part i including ptmt 25mm bore ball valve high pressure with epoxy coated aluminium rod and high density plastic ball , two nos new tank nipples of ptmt material 20 / 25mm bore dia as required completeallas specified & directed. 103 supply and fixaluminum frame duly powder coated ( minimum thickness of powder coating 50 micron ) for doors, windows, ventilators with one or more rebates including jointing cleats for fixing each other etc. completeallas specified & directed. 104 s & f aluminium sliding windows shutters powder coated ( minimum thickness of powder coating 50 micron ) including powder coated main frame, three track ( two for glazed and one for wire mesh ) without sash barsincluding necessary jointing cleats, glazing clips, epdm rubber packing, powder coated aluminium snap beading, screws, wheels, locking arrangments, suitable handles for sliding purpose, 4mm thick dark black tint plain glass and stainless steel wire mesh of dia 0.36mm and 1.40mm width of aperature, silicon chemical filling at gaps between section frame and wall surfaces completeallas specified and directed with the following sections of sliding window : ( a ) main frame bottom section : jindal section no 20798 ( b ) main frame top & sides section : jindal section no 20678 ( c ) sliding shutter section ( handle ) : jindal section no 20707 ( d ) sliding shutter section for top & bottom : jindal section no 20842 ( e ) sliding shutter section for interlock : jindal section no 21091 105 s & f aluminium window and ventilator shutters powder coated ( minimum thickness of powder coating 50 micron ) , side hung type without sash bars, aluminium sections of not less than 60mm width &1.50mm thick including necessary joining cleats, glazing clips, epdm rubber packing, snap beading, screws, peg stays 150mm long ( 1 no. per window ) , hinges 100mm long ( 2 / 3 nos. ) suitable handle ( 1 no. ) completeallasspecified & directed. 106 supply and fixaluminium section of approved design / pattern grills duly powder coated ( minimum thickness of powder coating 50 micron ) , with approved standard section and fixed to the existing window frame with c.p. brass / stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved powder coated aluminium section frame of standard section around the opening complete in all respect as specified and directed. 107 supply and fix sheet glass pane of 4mm thickness, ordinary quality, in squares, not exc 0.5 sqm each pane with solar control film 50micron reflective type sticked to glass pane completeallas specified and directed. 108 supply and fix stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws / first class wooden beadings completeallall as specified & directed. 109 supply and fix for factory made single extruded wpc ( wood polymer composite ) solid door / window / ceosetory windows & other frames / chowkhat of size 45 x 70 mm comprising of virgin pvc polymer of k value 58 60 ( suspension grade ) , calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying pvc solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750 kg / cum, screw withdrawal strength of 2200 n ( face ) & 1100 n ( edge ) , minimum compressive strength of 58 n / mm² , modules of elasticity 900 n / mm²and resistance to spread of flame of class a category with property of being termite / borer proof, water / moisture proof and fire retardant and fixed in position with ms hold fast / lugs / ss dash fasteners of required dia and length complete as directed. 110 note : ( a ) m.s. hold fast / lugs or ss dash fasteners shall be paid for separately ( b ) wpc solid door / window frames, minus upto 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made 111 supply and fix second class hardwood plain solid straight chowkhat and frame wrought framed rebated on the solid rounded or chamfered but together with glue pinned at joint complete all as specified & directed. 112 supply and fix of stainless steel handles 100mm size, d type dotted for kitchen / cup board cabinet shutters complete all as specified and directed. 113 supply and fix stainless steel telescopic channel 45mm x 20 inch, ball bearing runners, full extension, load capacity 50 kgs fixed to drawer complete all as specified and directed. 114 supply and fix mild steel ordinary rat tail rod pattern springs300mm including roller and roller plate of soft closing pattern including welding to frame as required completeallas specified & directed. 115 material and labour preparation ofnew wooden surface duly filled the voids with enamel based puttyover 10cm width or girthand applying two coats of syntheticenemal paint over a coat of pink primer allas specified & directed. 116 material and labourpreparation of old decorated painted wood and wood based surfaces of any description duly filled the voids with enamel based putty, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paintcompleteallas specified & directed. 117 material and labourpreparation of old steel surfaces of any description duly filled the voids with enamel based putty, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paintcompleteallas specified & directed. 118 supply and fix in repairscurtain rodsstainless steel 25mm dia, decorative typeincluding fixing end brackets, middle brackets , stops, etc. completeallas specified & directed. 119 supply and fix mild steel window guard bars, hold fasts of plain / square conforming to fe 290, gde e 165 and fixed in walls of any description including bed blocks cutting, angle iron / flat iron frame of approved design and similar articles completeallas specified & directed. 120 material and labour preparation of new steel surfaces of any descriptionduly filled the voids with enamel based putty, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primercompleteallas specified & directed. 121 material and labour preparation of newly plastered wall surfaces and applying 2mm thick wall care putty in two coats, two coats of oil bound distemper over a coat of self primerusing spunge roller completeallas specified & directed. 122 material and labour preparation ofnewly plasterd ceiling surfaces including necessary filling of voids with wall care puttyand applying three coats of white washcompleteallas specified & directed. 123 material & labour preparation ofnew surfaces and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqmcompleteallas specified & directed. 124 material and labourcomplete removal of existing treatment and painted surfaces and applying 2mm thick wall care putty in two coats on walls, pillasters, cornices etc, two coats of oil bound distemperusing spunge roller over one coat of self primer all as specified & directed. 125 material & labourcomplete removal of existing treatmentfor applying twocoats ofacrylic emulsion paintof alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives over and including priming coat of exterior primer applied on old decorated surfacesofwalls including necessary filling of voids with wall care putty complete in all respect as specified & directed. 126 material & labour preparation of old treated ceiling surfacesincluding necessary filling of voids with wall care putty and applying two coats of white wash completeallas specified & directed. 127 supply and fix g i wire netting 0.90mm dia and 12mm square mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting, waste and cutting in plaster, concrete / stone surafce in patches completeallas specified & directed. 128 material and labour high density polyethylene pipes ( hdpe ) 50mm bore dia and fittings of pressure rating 6kgf / cm² fixed complete to walls, ceilings or in floors as drain out pipe etc., including necessary cutting and chasing in wall or floor of any description completeallas specified & directed. 129 supply and fixpre polished ( table rubbed and polished ) machine cut granite stone work, 16 18mm thick ( of any type & size ) in steps ( treads ) , window / door cills, cooking platforms, wash hand basin counter and like bedded and jointed with grey cement slurry with 20mm thick cement mortar ( 1:4 ) including pointing in white cement with pigment to match with shade of granite and cutting for circular holes of any dia for fixing sanitary fittings or of simialr work completeallas specified & directed. 130 supply and fixpre polished ( table rubbed and polished ) machine cut granite stone work, 16 18mm thick ( of any type & size ) in steps ( risers ) , jambs, pillars, dado / skirting and like laid over cement screed bedded with 15mm thick cement mortar ( 1:4 ) and jointed with grey cement slurryincluding pointing in white cement with pigment to match with shade of granite and cutting for circular holes of any dia for fixing sanitary fittings or of simialr work completeallas specified & directed. 131 supply and fixed in repair ball valves high pressure of ptmt with epoxy coated aluminiumrod& high density plastic ball screwed for iron / cpvc / ppr pipe 20mm dia and fixed complete in all respect as specified & directed. 132 supply and fixed in repair ball valves high pressure of ptmt with epoxy coated aluminiumrod& high density plastic ball screwed for iron / cpvc / ppr pipe 25mm dia and fixed complete in all respect as specified & directed. 133 material and labour for full round and polished moulding ( as per main stone polish ) to edges of stone slabs upto 20mm thick, such as in window cill, jambs, counters, steps etc. and of other similar situations completeallas specified & directed. 134 supply and fixed in repair pillar taps, fancy swan neckcast copper alloy chromium plated, with capstan heads, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe 15mm dia completeallas specified & directed. 135 dismantling of existing water storage tank and supply, hoisting and fixing of double layer, isi marked, 500 litre rotational moulded polyethylene water storage tank ( cylindrical vertical with closed top ) fixed in position all as specified in ssr part i including ptmtball valve 25mm bore, high pressure with epoxy coated aluminium rod and high density plastic ball completeallas specified & directed. 136 s & f in repairs health faucet ( abs body ) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete as specified and directed. 137 excavation in trenches not exceeding 1.5m depth and not exceeding 1.5m wide and getting out in hard / dense soilall as specified and directed. 138 returning and filling in soil including spreading levelling watering and well ramming in layers not exceeding 25cm all as specified and directed. 139 removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed. 140 taking up or down steel tubing 100 mm dia pipe along with fittings such as tee, bends etc fixed to walls and ceilings or laid in floors / trenchesand connections including removal from sitecomplete all as specified as directed. 141 all as per item no 139 herein before but 80mm dia 142 all as per item no139 herein before but 50mm dia 143 all as per item no139 herein before but 40mm dia 144 all as per item no 139 herein before but 25mm dia 145 s & f galvanised iron tubing medium grade with all new connections and fittings such as tees, bends, elbows, short pieces, connector back nuts, diminishing pieces, caps, plugs unions etclaid in trenches for 100 mm size of pipes complete all as specified and as directed 146 all as per item no144 herein before but 80mm dia 147 all as per item no144 herein before but 50mm dia 148 all as per item no144 herein before but 40mm dia 149 s & f gi tubing medium grade with all new connections and fittings such as tees, bends, elbows, short pieces, connector back nuts, diminishing pieces, caps, plugs unions etcfixed complete to walls and ceiling or laid in floors for 25 mm size of pipes complete all as specified and as directed 150 supply and fix gun metal, globe orgate valveswith iron wheel head, screwed both ends for iron pipe 50 mm dia including taking down old unserviceable one complete all as specified and directed 151 all as per item no 149 herein before but 40mm dia 152 s & fstreet / building mounted light fitting astra neo led 25 watt, pressure die cast housing, toughened glass and high power leds with secondary optics, ip 66 protection including necessary fixing arrangement i.e. gi clamps, nuts bolts and washers etcincluding taking down old unserviceablefitting all as specified and directed 153 s & fstreet / building mounted light fitting astra neo led 30 watt, pressure die cast housing, toughened glass and high power leds with secondary optics, ip 66 protection including necessary fixing arrangement i.e. gi clamps, nuts bolts and washers etcincluding taking down old unserviceablefitting all as specified and directed 154 s & f street / building mounted light fitting astra neo led 45 watt, pressure die cast housing, toughened glass, high power leds with secondary optics, ip 66 protection including necessary fixing arrangement i.e. gi clamps, nuts bolts and washers etcincluding taking down old un serviceablefitting all as specified and directed. 155 s & f bracket for street light fitting made out of 40 mm dia light grade gi tubing bend to required shape 1.5 m long including necessary gi clamps, nuts bolts and washers and fixing to the pole complete including taking down old rusted bracket including clamps, nut & boltsfrom the pole as directed. 156 s & f frp junction box of size 295 mm x 255 mm x 160 mm with self locking arrangementcomprising of one no mcb sp 06 amps with suitable din chanel, 4 way 32a pvc connectorfixed to pole with flat iron clamps of size 25x4 mm, nuts and boltsand connecting the incoming and out going cables, including taking down old existing unserviceable junction box all asspecified & directed. 157 s & fpower contactor 3 pole, 32 amps rated capacity 50 cycles 220 / 240 volts including incoming& outgoing wiring with copper conductor of 10 sq mm size with suitable copper lugs and taking down the existing unserviceable contactor complete all as directed. 158 s & f analog time switch ( with battery backup ) 3p module, 24 hours program, programmable every 15 min, back up of 100 hours current carryingcapacity 16 ampwith changeover ( 1 c0 ) , 240 volts single phase automatic switch on / off operation of street lights in the evening and morning respectively at selected time, proper serviceability including taking down existing unserviceable switch all as specified & directed. 159 m & lpvc insulated flat twin core sheathed cables, stranded aluminium conductor1.1kv grade of size 6 sqmm cable including taking down old cable all as specified & directed. 160 m & lpvc insulated flat twin core sheathed cablesstandard aluminium conductor1.1kv grade of size 10 sqmm cable including taking down old cable all as specified & directed. 161 m & lpvc insulated flat twin core sheathed cablesstandard aluminium conductor1.1kv grade of size 16 sqmm cable including taking down old cable all as specified & directed. 162 cutting the tar macadam road / hard standings for laying cable and excavating not exceeding 0.45m wide and 0.60mdepth and getting out all as directed including filing back soil, ramming watering etc and finishingwith 200mm thick pcc 1:2:4 type b 2matching with the surroundings all as specified & directed. 163 s & f in repairs earth continiuty conductor or main earthing lead 32×6 mm galvanised iron strip with proper saddles / spacer, screw etc, fixed on wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to pole or any other indicated situation for loop earthing etc, as requiredalll as specified and directed. 164 s & f in repairs earth continiuty conductor or main earthing lead 4 mm dia galvanised iron wire with proper saddles / spacer, screw etc, fixed on wall on batten or recess or chases or buired in ground or drawn in conduit / pipe or fixed to pole or any other indicated suituation for loop earthing etc, as requiredalll as specified and directed. 165 supply only common salt commercial all as directed complete all as specified and as directed. 166 supply only of charcoal dust complete all as specified and as directed. 167 repairing and maintenance of old existing earth pit by taking out carefully earth plate, watering pipe, earth lead protection pipe and re installation the same after removing sludge from the plate & pipes including re connection / brazing the plate and strip, as required at site ( earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of earth plate not less than 1.5 metres below normal ground level, includingpcc 1:3:6 type c1 pit chamber with cover of rcc 1:2:4 type b1, reinforced with welded steel wire fabric not less than 4 kg per sqm with handle and angle iron frame, watering arrangment with 20 mm bore gi medium grade pipe isi marked, gi funnel with gi mesh, filling with mixture of common salt and charcoal, necessary excavation, refilling, removing away soil and earth work in any type of soil including testing and commissioning complete all as specifed and as directed. 168 note : gi funnel, brazing, mixture of salt / char coal shall be measured and paid separately under releavant items. 169 supply only gi funnels for earthing complete all as specified and as directed. 170 m & l in repairearthing chamber of inner size 0.45 x 0.45x 0.45 m with 100 mm thick by pcc 1:3:6 type c1 foundation & walls, rcc 1:2:4 type b1 with wire mesh reinforcement in cover slab complete all as specified and as directed. 171 material andlabour fortesting of earth resistancevalue from earthing pit test terminal pointand write in / on existingidentification board complete all as specified and as directed.note: ( i ) the contractor shall providehis own testing kit ( make: fluke ) and all connected items for earthresistance checking complete. ( ii ) test result shall be submitted to engr in charge. 172 m & l earthing and testing complete with galvanized iron earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 m below normal ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to and including gi wire 4 mm dia as earth lead by means of bolts and nuts, check nuts and washers etc made of gi & connected to equipment and earthing test point , earth dolly all as shown in elect plate no 3 of ssr pt i includingnecessary earth work, excavation pcc chamber with rcc 1:2:4 cover including handle, 20mm dia gi watering pipe, 25 mm dia light grade gi for protection of earth strip, wire mesh, funnel, charcoal dust & common salt, testing on completion etc completeall as specified & directed 173 s & f earth pit marker / indicator of triangle size ( 1 feet each side ) , fitted with gi pipe25mm dia and fixed in ground by grouting in pcc 1: 2:4 complete all as specifed and directed.note: height of gi pipe should be 3 feet above from the ground level, colour coding red colour for chemical earth pits and yellow colour for conventional earth pits. 174 s & f led light fitting driver of following specification complete all as specified and directed: 175 25 w led driver 176 45 w led driver 177 70 w led driver 178 100 w led driver 179 200 w led driver 180 250 w led driver...
Due Date : November 30, 2023
Tender Value : ₹ Ref. Documents
